XFillRectangle(3X11) manual page

Name

XFillRectangle, XFillRectangles, XFillPolygon, XFillArc, XFillArcs - fill rectangles, polygons, or arcs

Syntax

XFillRectangle(display, d, gc, x, y, width, height)
Display *display;

Drawable d;

GC gc;

int x, y;

unsigned int width, height;

XFillRectangles(display, d, gc, rectangles, nrectangles)
Display *display;

Drawable d;

GC gc;

XRectangle *rectangles;

int nrectangles;

XFillPolygon(display, d, gc, points, npoints, shape, mode)
Display *display;

Drawable d;

GC gc;

XPoint *points;

int npoints;

int shape;

int mode;

XFillArc(display, d, gc, x, y, width, height, angle1, angle2)
Display *display;

Drawable d;

GC gc;

int x, y;

unsigned int width, height;

int angle1, angle2;

XFillArcs(display, d, gc, arcs, narcs)
Display *display;

Drawable d;

GC gc;

XArc *arcs;

int narcs;

Arguments

angle1: Specifies the start of the arc relative to the three-o'clock position from the center, in units of degrees * 64.
angle2: Specifies the path and extent of the arc relative to the start of the arc, in units of degrees * 64.
arcs: Specifies an array of arcs.
d: Specifies the drawable.
display: Specifies the connection to the X server.
gc: Specifies the GC.
mode: Specifies the coordinate mode. You can pass CoordModeOrigin or CoordModePrevious.
narcs: Specifies the number of arcs in the array.
npoints: Specifies the number of points in the array.
nrectangles: Specifies the number of rectangles in the array.
points: Specifies an array of points.
rectangles: Specifies an array of rectangles.
shape: Specifies a shape that helps the server to improve performance. You can pass Complex, Convex, or Nonconvex. or the major and minor axes of the arc
width
height: Specify the width and height, which are the dimensions of the rectangle to be filled and specify the upper-left corner of the rectangle
x
y: Specify the x and y coordinates, which are relative to the origin of the drawable

Description

The XFillRectangle and XFillRectangles functions fill the specified rectangle or rectangles as if a four-point FillPolygon protocol request were specified for each rectangle:

[x,y] [x+width,y] [x+width,y+height] [x,y+height]

Each function uses the x and y coordinates, width and height dimensions, and GC you specify.

XFillRectangles fills the rectangles in the order listed in the array. For any given rectangle, XFillRectangle and XFillRectangles do not draw a pixel more than once. If rectangles intersect, the intersecting pixels are drawn multiple times.

Both functions use these GC components: function, plane-mask, fill-style, subwindow-mode, clip-x-origin, clip-y-origin, and clip-mask. They also use these GC mode-dependent components: foreground, background, tile, stipple, tile-stipple-x-origin, and tile-stipple-y-origin.

XFillRectangle and XFillRectangles can generate BadDrawable, BadGC, and BadMatch errors.

XFillPolygon fills the region closed by the specified path. The path is closed automatically if the last point in the list does not coincide with the first point. XFillPolygon does not draw a pixel of the region more than once. CoordModeOrigin treats all coordinates as relative to the origin, and CoordModePrevious treats all coordinates after the first as relative to the previous point.

Depending on the specified shape, the following occurs:

If shape is Complex, the path may self-intersect. Note that contiguous coincident points in the path are not treated as self-intersection.
If shape is Convex, for every pair of points inside the polygon, the line segment connecting them does not intersect the path. If known by the client, specifying Convex can improve performance. If you specify Convex for a path that is not convex, the graphics results are undefined.
If shape is Nonconvex, the path does not self-intersect, but the shape is not wholly convex. If known by the client, specifying Nonconvex instead of Complex may improve performance. If you specify Nonconvex for a self-intersecting path, the graphics results are undefined.

The fill-rule of the GC controls the filling behavior of self-intersecting polygons.

This function uses these GC components: function, plane-mask, fill-style, fill-rule, subwindow-mode, clip-x-origin, clip-y-origin, and clip-mask. It also uses these GC mode-dependent components: foreground, background, tile, stipple, tile-stipple-x-origin, and tile-stipple-y-origin.

XFillPolygon can generate BadDrawable, BadGC, BadMatch, and BadValue errors.

For each arc, XFillArc or XFillArcs fills the region closed by the infinitely thin path described by the specified arc and, depending on the arc-mode specified in the GC, one or two line segments. For ArcChord, the single line segment joining the endpoints of the arc is used. For ArcPieSlice, the two line segments joining the endpoints of the arc with the center point are used. XFillArcs fills the arcs in the order listed in the array. For any given arc, XFillArc and XFillArcs do not draw a pixel more than once. If regions intersect, the intersecting pixels are drawn multiple times.

Both functions use these GC components: function, plane-mask, fill-style, arc-mode, subwindow-mode, clip-x-origin, clip-y-origin, and clip-mask. They also use these GC mode-dependent components: foreground, background, tile, stipple, tile-stipple-x-origin, and tile-stipple-y-origin.

XFillArc and XFillArcs can generate BadDrawable, BadGC, and BadMatch errors.

Diagnostics

BadDrawable: A value for a Drawable argument does not name a defined Window or Pixmap.
BadGC: A value for a GContext argument does not name a defined GContext.
BadMatch: An InputOnly window is used as a Drawable.
BadMatch: Some argument or pair of arguments has the correct type and range but fails to match in some other way required by the request.
BadValue: Some numeric value falls outside the range of values accepted by the request. Unless a specific range is specified for an argument, the full range defined by the argument's type is accepted. Any argument defined as a set of alternatives can generate this error.

Name

Syntax

Arguments

Description

Diagnostics

See Also