INTERNET DRAFT R. Boivie, N. Feldman IBM Y. Imai Fujitsu W. Livens Colt Telecom D. Ooms OneSparrow O. Paridaens Alcatel E.Muramoto Panasonic June, 2004 Expires December, 2004 Explicit Multicast (Xcast) Basic Specification Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract Multicast has become increasingly important with the emergence of network-based applications such as IP telephony and video conferencing. The Internet community has done a significant amount of work on IP multicast over the last decade [1075, 2201, 2236, DEER, DEE2, FARI, HOLB, MBONE, PERL]. Ooms, et al. Expires December 2004 [Page 1] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 However, while traditional multicast schemes are scalable in the sense that they can support very large multicast groups, there are scalability issues when a network needs to support a very large number of distinct multicast groups. This document describes a new scheme for multicast - named Explicit Multicast (Xcast) - that complements the existing schemes. Whereas the existing schemes can support a limited number of very large multicast sessions, Xcast can support a very large number of small multicast sessions. This is achieved by explicitly encoding the list of destinations in the data packets, instead of using a multicast address. The co-operation of Xcast - a data plane mechanism - with existing control planes is described and scenarios for gradual deployment are investigated. Encodings for both IPv4 and IPv6 are proposed. This draft merges three earlier drafts ([BOIV], [IMAI], [OOMS]). Table of Contents 1. Introduction 2. Xcast Overview 3. The cost of the traditional multicast schemes 4. Motivation 5. Application 6. Xcast Flexibility 7. Control plane 7.1. SIP 7.2. Receiver Initiated Join model 8. Optional information 8.1. List of ports 8.2. List of DSCPs 8.3. Channel Identifier 9. Encoding 9.1. General 9.2. IPv4 9.2.1. IPv4 header 9.2.2. Xcast4 header 9.3. IPv6 9.3.1. IPv6 header 9.3.2. Xcast6 header 9.3.2.1. Routing Extension header 9.3.2.2. Destination Extension header 10. Impact on Upper Layer Protocols 10.1. Checksum calculation in UDP and ICMP 10.2. IPsec Authentication header Ooms, et al. Expires December 2004 [Page 2] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 11. Gradual Deployment 11.1. Tunneling 11.2. Premature X2U 11.3. Semi-permeable tunneling (IPv6 only) 11.4. Special case: deployment without network support 11.5. Using a Small Number of Xcast-Aware Routers to Provide Xcast in a Not-so-Small Network 12. (Socket) API 13. Security Considerations References Changes: 00->01: - added Channel Identifier in Xcast header - cleaned up wording (traditional, current, today's mc) - added definition of Session and Channel 01->02: - Channel Identifier in the Xcast4 header was moved higher - editorial changes 02->03: - clarified meaning of X-bit and the application of X2U - added section 11.5 03->04: - clarification of NBR_OF_DEST 04->05: - no changes 05->06: - updated contact information 1. Introduction Multicast, the ability to efficiently send data to a group of destinations, is becoming increasingly important for applications such as IP telephony and video-conferencing. There seem to be two kinds of multicast that are important: a broadcast-like multicast that sends data to a very large number of destinations and a "narrowcast" multicast that sends data to a fairly small group. An example of the first is the audio and video multicasting of a presentation to all employees in a corporate intranet. An example of the second is a videoconference involving 3 or 4 parties. For reasons described below, it seems prudent to use different mechanisms for these two cases. As the reliable multicast transport group has stated: "it is believed that a 'one size fits all' protocol will be unable to meet the requirements of all applications" [RMT]. Note too, that [2902], "Overview of the 1998 IAB Routing Workshop", also came to the same conclusion: "For example, providing for many groups of small conferences (a small number of widely dispersed people) with global topological scope scales badly given the current multicast model". Today's multicast schemes can be used to minimize bandwidth consumption. Explicit Multicast (Xcast) also can be used to minimize bandwidth consumption for "small groups". But it has an additional Ooms, et al. Expires December 2004 [Page 3] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 advantage as well. Xcast eliminates the per session signaling and per session state information of traditional multicast schemes and this allows Xcast to support very large numbers of multicast sessions. And this scalability is important since it enables important classes of applications such as IP telephony, videoconferencing, collaborative applications, networked games etc. where there are typically very large numbers of small multicast groups. 2. Xcast Overview In this document the following terminology will be used: - Session: in Xcast the term 'multicast session' will be used instead of 'multicast group' to avoid the strong association of multicast groups with multicast group addresses in traditional IP multicast. - Channel: in a session with multiple senders (e.g. a video conference), the flow sourced by one sender will be called a channel. So a session can contain one or more channels. In the Host Group Model the packet carries a multicast address as a logical identifier of all group members. In Xcast, the source node keeps track of the destinations in the multicast channel that it wants to send packets to. The source encodes the list of destinations in the Xcast header, and then sends the packet to a router. Each router along the way parses the header, partitions the destinations based on each destination's next hop, and forwards a packet with an appropriate Xcast header to each of the next hops. When there is only one destination left, the Xcast packet can be converted into a normal unicast packet, which can be unicasted along the remainder of the route. This is called X2U (Xcast to Unicast). For example, suppose that A is trying to get packets distributed to B, C & D in Figure 1 below: Ooms, et al. Expires December 2004 [Page 4] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 R4 ---- B / / A----- R1 ---- R2 ---- R3 R8 ---- C \ / \ / R5 ---- R6 ---- R7 \ \ R9 ---- D Figure 1 This is accomplished as follows: A sends an Xcast packet with the list of destinations in its Xcast header to the first router, R1. Since the Xcast header will be slightly different for IPv4 and IPv6 we won't reveal any details on the encoding of the Xcast header in this section (see section 9). So, ignoring the details, the packet that A sends to R1 looks like this: [ src = A | dest = B C D | payload ] When R1 receives this packet, it needs to properly process the Xcast header. The processing that a router does on receiving one of these Xcast packets is as follows: - Perform a route table lookup to determine the next hop for each of the destinations listed in the packet. - Partition the set of destinations based on their next hops. - Replicate the packet so that there's one copy of the packet for each of the next hops found in the previous steps. - Modify the list of destinations in each of the copies so that the list in the copy for a given next hop includes just the destinations that ought to be routed through that next hop. - Send the modified copies of the packet on to the next hops. - Optimization: If there is only one destination for a particular next hop, the packet can be sent as a standard unicast packet to the destination (X2U). So, in the example above, R1 will send a single packet on to R2 with a destination list of < B C D > and R2 will send a single packet to R3 with the same destination list. Ooms, et al. Expires December 2004 [Page 5] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 When R3 receives the packet, it will, by the algorithm above, send one copy of the packet to next hop R5 with an Xcast list of < C D >, and one ordinary unicast packet addressed to < B > to R4. R4 will receive a standard unicast packet and forward it on to < B >. R5 will forward the Xcast packet that it receives on to R6 which will pass it on to R7. When the packet reaches R7, R7 will transmit ordinary unicast packets addressed to < C > and < D > respectively. R8 and R9 will receive standard unicast packets, and forward the packets on to < C > and < D > respectively. It's important that the Xcast packet that is sent to a given next hop only includes destinations for which that next hop is the next hop listed in the route table. If the list of destinations in the packet sent to R4, for example, had also included C and D, R4 would send duplicate packets. Note that when routing topology changes, the routing for an Xcast channel will automatically adapt to the new topology since the path an Xcast packet takes to a given destination always follows the ordinary, unicast routing for that destination. 3. The cost of the traditional multicast schemes Traditional multicast schemes [DEER, DEE2, FARI] were designed to handle very large multicast groups. These work well if one is trying to distribute broadcast-like channels all around the world but they have scalability problems when there is a very large number of groups. The characteristics of the traditional IP multicast model are determined by its two components: the Host Group model [DEER] and a Multicast Routing Protocol. Both components make multicast very different from unicast. In the Host Group model, a group of hosts is identified by a multicast group address, which is used both for subscriptions and forwarding. This model has two main costs: - Multicast address allocation: The creator of a multicast group must allocate a multicast address which is unique in its scope (scope will often be global). This issue is being addressed by the Malloc working group, which is proposing a set of Multicast Address Allocation Servers (MAAS) and three protocols (MASC, AAP, MADCAP). - Destination unawareness: When a multicast packet arrives in a router, the router can determine the next hops for the packet, but Ooms, et al. Expires December 2004 [Page 6] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 knows nothing about the ultimate destinations of the packet, nor about how many times the packet will be duplicated later on in the network. This complicates the security, accounting and policy functions. In addition to the Host Group model, a routing algorithm is required to maintain the member state and the delivery tree. This can be done using a (truncated) broadcast algorithm or a multicast algorithm [DEER]. Since the former consumes too much bandwidth by unnecessarily forwarding packets to some routers, only the multicast algorithms are considered. These multicast routing protocols have the following costs: - Connection state: The multicast routing protocols exchange messages that create state for each (source, multicast group) in all the routers that are part of the point-to-multipoint tree. This can be viewed as "per flow" signaling that creates multicast connection state, possibly yielding huge multicast forwarding tables. Some of these schemes even disseminate this multicast routing information to places where it isn't necessarily needed [1075]. Other schemes try to limit the amount of multicast routing information that needs to be disseminated, processed and stored throughout the network. These schemes (e.g. [2201]) use a "shared distribution tree" that is shared by all the members of a multicast group and they try to limit the distribution of multicast routing information to just those nodes that "really need it". But these schemes also have problems. Because of the shared tree, they use less than optimal paths in routing packets to their destinations and they tend to c! oncentrate traffic in small portions of a network. And these schemes still involve lots of "per flow" signaling and "per flow" state. - Source advertisement mechanism: Multicast routing protocols provide a mechanism by which members get 'connected' to the sources for a certain group without knowing the sources themselves. In sparse-mode protocols [2201, DEE2], this is achieved by having a core node, which needs to be advertised in the complete domain. On the other hand, in dense-mode protocols [1075] this is achieved by a "flood and prune" mechanism. Both approaches raise additional scalability issues. - Interdomain routing: Multicast routing protocols that rely on a core node [2201, DEE2] additionally need an interdomain multicast routing protocol (e.g. [FARI]). The cost of multicast address allocation, destination unawareness and the above scalability issues lead to a search for other multicast Ooms, et al. Expires December 2004 [Page 7] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 schemes. Source-Specific Multicast (SSM) [HOLB] addresses some of the above drawbacks: in SSM a host joins a specific source, thus the channel is identified by the couple (source address, multicast address). This approach avoids multicast address allocation as well as the need for an interdomain routing protocol. The source advertisement is taken out of the multicast routing protocol and is moved to an out-of-band mechanism (e.g. web page). Note that SSM still creates state and signaling per multicast channel in each on-tree node. Figure 2 depicts the above costs as a function of the number of members in the session or channel. All the costs have a hyperbolic behavior. cost of the traditional multicast model per member ^ | costly| OK | <-----|-----> | . | | .. | | ..|.. | | ......... | | ........ +---------------------------> | number of members v alternative=Xcast Figure 2 The traditional multicast model becomes expensive for its members if the groups are small. Small groups are typical for conferencing, gaming and collaborative applications. These applications are well- served by Xcast. In practice, traditional multicast routing protocols impose limitations on the number of groups and the size of the network in which they are deployed. For Xcast these limitations do not exist. 4. Motivation Xcast takes advantage of one of the fundamental tenets of the Internet "philosophy", namely that one should move complexity to the edges of the network and keep the middle of the network simple. This is the principle that guided the design of IP and TCP and it's the principle that has made the incredible growth of the Internet Ooms, et al. Expires December 2004 [Page 8] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 possible. For example, one reason that the Internet has been able to scale so well is that the routers in the core of the network deal with large CIDR blocks as opposed to individual hosts or individual "connections". The routers in the core don't need to keep track of the individual TCP connections that are passing through them. Similarly, the IETF's diffserv effort is based on the idea that the routers shouldn't have to keep track of a large number of individual RSVP flows that might be passing through them. It's the authors' belief that the routers in the core shouldn't have to keep track of a large number of individual multicast flows either. Compared to traditional multicast, Xcast has the following advantages: 1) Routers do not have to maintain state per session (or per channel) [SOLA]. This makes Xcast very scalable in terms of the number of sessions that can be supported since the nodes in the network do not need to disseminate or store any multicast routing information for these sessions. 2) No multicast address allocation required. 3) No need for multicast routing protocols (neither intra- nor interdomain). Xcast packets always take the "right" path as determined by the ordinary unicast routing protocols. 4) No core node, so no single point of failure. Unlike the shared tree schemes, Xcast minimizes network latency and maximizes network "efficiency". 5) Symmetric paths are not required. Traditional multicast routing protocols create non-shortest-path trees if paths are not symmetric. (A path between two nodes A and B is symmetric if the path is both the shortest path from A to B as well as the shortest path from B to A.) It is expected that an increasing number of paths in the Internet will be asymmetric in the future as a result of traffic engineering and policy routing, and thus the traditional multicast schemes will result in an increasing amount of suboptimal routing. 6) Automatic reaction to unicast reroutes. Xcast will react immediately to unicast route changes. In traditional multicast routing protocols a communication between the unicast and the multicast routing protocol needs to be established. In many implementations this is on a polling basis, yielding a slower reaction to e.g. link failures. It may also take some time for traditional multicast routing protocols to fix things up if there is a large number of groups that need to be fixed. Ooms, et al. Expires December 2004 [Page 9] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 7) Easy security and accounting. In contrast with the Host Group Model, in Xcast all the sources know the members of the multicast channel, which gives the sources the means to e.g. reject certain members or count the traffic going to certain members quite easily. Not only a source, but also a border router is able to determine how many times a packet will be duplicated in its domain. It also becomes easier to restrict the number of senders or the bandwidth per sender. 8) Heterogeneous receivers. Besides the list of destinations, the packet could (optionally) also contain a list of DiffServ CodePoints (DSCPs). While traditional multicast protocols have to create separate groups for each service class, Xcast incorporates the possibility of having receivers with different service requirements within one multicast channel. 9) Xcast packets can make use of traffic engineered unicast paths. 10) Simple implementation of reliable protocols on top of Xcast, because Xcast can easily address a subset of the original list of destinations to do a retransmission. 11) Flexibility (see section 6). 12) Easy transition mechanisms (see section 11). It should be noted that Xcast has a number of disadvantages as well: 1) Overhead. Each packet contains all remaining destinations. But, the total amount of data is still much less than for unicast (payload is only sent once). A method to compress the list of destination addresses might be useful. 2) More complex header processing. Each destination in the packet needs a routing table lookup. So an Xcast packet with n destinations requires the same number of routing table lookups as n unicast headers. Additionally, a different header has to be constructed per next hop. Note however that: a) Since Xcast will typically be used for super-sparse sessions, there will be a limited number of branching points, compared to non-branching points. Only in a branching point do new headers need to be constructed. b) The header construction can be reduced to a very simple operation: overwriting a bitmap. c) Among the non-branching points, a lot of them will contain only Ooms, et al. Expires December 2004 [Page 10] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 one destination. In these cases normal unicast forwarding can be applied. d) By using a hierarchical encoding of the list of destinations in combination with the aggregation in the forwarding tables the forwarding can be accelerated ([OOMS]). e) When the packet enters a region of the network where link bandwidth is not an issue anymore, the packet can be transformed by a Premature X2U. Premature X2U (see section 11.2) occurs when a router decides to transform the Xcast packet for one or more destinations into unicast packets. This avoids more complex processing downstream. f) Other mechanisms to reduce the processing have been described in [IMAI] (tractable list) and [OOMS] (caching), but are not (yet) part of this basic Xcast specification. 3) Xcast only works with a limited number of receivers. 5. Application While Xcast is not suitable for multicast sessions with a large number of members, such as the broadcast of an IETF meeting, it does provide an important complement to existing multicast schemes in that it can support very large numbers of small sessions. Thus Xcast enables important applications such as IP telephony, videoconferencing, multi-player games, collaborative e-meetings etc. The number of these sessions will become huge. Some may argue that it is not worthwhile to use multicast for sessions with a limited number of members, and use unicast instead. But in some cases limited bandwidth in the "last mile" makes it important to have some form of multicast as the following example illustrates. Assume n residential users that set up a video conference. Typically access technologies are asymmetric (e.g. xDSL, GPRS or cable modem). So, a host with xDSL has no problem receiving n-1 basic 100kb/s video channels, but the host is not able to send its own video data n-1 times at this rate. Because of the limited and often asymmetric access capacity, some type of multicast is mandatory. A simple but important application of Xcast lies in bridging the access link. The host sends the Xcast packet with the list of unicast addresses and the first router performs a Premature X2U. Since Xcast is not suitable for large groups, Xcast will not replace Ooms, et al. Expires December 2004 [Page 11] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 the traditional multicast model, but it does offer an alternative for multipoint-to-multipoint communications when there can be very large numbers of small sessions. 6. Xcast Flexibility The main goal of multicast is to avoid duplicate information flowing over the same link. By using traditional multicast instead of unicast, bandwidth consumption decreases while the state and signaling per session increases. Xcast has a cost of 0 in these 2 dimensions, but it does introduce a third dimension corresponding to the header processing per packet. This three dimensional space is depicted in Figure 3. state&signaling per session in router ^ | | .... B | .... . | .... . | .... . | .... . +------------------..---> processing . / .... C per packet . / ..... in router . / ..... . / ..... ./ ..... /A.... / / link bandwidth Figure 3 One method of delivering identical information from a source to n destinations is to unicast the information n times (A in Figure 3). A second method, the traditional multicast model (B in Figure 3) sends the information only once to a multicast address. In Xcast the information is sent only once, but the packet contains a list of destinations (point C). The three points A, B and C define a plane (indicated with dots in Ooms, et al. Expires December 2004 [Page 12] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 Figure 3): a plane of conservation of misery. All three approaches have disadvantages. The link bandwidth is a scarce resource, especially in access networks. State&signaling/session encounters limitations when the number of sessions becomes large and an increased processing/packet is cumbersome for high link speeds. One advantage of Xcast is that it allows a router to move within this plane of conservation of misery based upon its location in a network. For example in the core of the network, a cache could be used to move along the line from C to B without introducing any per-flow signaling. Another possibility, as suggested above, is to use premature X2U to move along the line from C to A in an access network if there is an abundance of bandwidth in the backbone. 7. Control plane Unlike traditional multicast schemes, Xcast does not specify a "control plane". There is no IGMP, and as mentioned above, there are no intradomain or interdomain multicast routing protocols. With Xcast, the means by which multicast sessions are defined is an application level issue and applications are not confined to the model in which hosts use IGMP to join a multicast session. For example: - some applications might want to use an IGMP-like receiver-join model. - other applications might want to use a model in which a user places a call to the party or parties that he or she wants to talk to (similar to the way that one puts together a conference call today using the button's on one's telephone). - one might define a session based on the cells that are close to a moving device in order to provide for a "smooth handoff" between cells when the moving device crosses cell boundaries. - in some applications the members of the session might be specified as arguments on a command line. - one might define an application that uses GPS to send video from a bank robbery to the 3 police cars that are closest to the bank being robbed. Thus, the application developer is not limited to the receiver- initiated joins of the IGMP model. There will be multiple ways in which an Xcast sender determines the addresses of the members of the channel. Ooms, et al. Expires December 2004 [Page 13] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 For the purpose of establishing voice and multimedia conferences over IP networks, several control planes have already been defined, including SIP [2543] and H.323[H323]. 7.1. SIP In SIP, a host takes the initiative to set up a session. With the assistance of a SIP server a session is created. The session state is kept in the hosts. Data delivery can be achieved by several mechanisms: meshed unicast, bridged or multicast. Note that for the establishment of multicast delivery, a multicast protocol and communication with Multicast Address Allocation Servers (MAAS) are still required. In "meshed unicast" or "multi-unicasting", the application keeps track of the participants' unicast addresses and sends a unicast to each of those addresses. For reasons described in section 3, multi- unicasting rather than multicast is the prevalent solution in use today. It's a simple matter to replace multi-unicast code with Xcast code. All that the developer has to do is replace a loop that sends a unicast to each of the participants by a single "xcast_send" that sends the data to the participants. Thus it's easy to incorporate Xcast into real conferencing applications. Both Xcast and SIP address super-sparse multicast sessions. It turns out that Xcast (a very flexible data plane mechanism) can be easily integrated with SIP (a very flexible control plane protocol). When an application decides to use Xcast forwarding it does not affect its interface to the SIP agent: it can use the same SIP messages as it would for multi-unicasting. 7.2 Receiver Initiated Join model In the previous section, it was discussed how to establish an Xcast session among well known participants of a multi-party conference. In some cases, it is useful for participants to be able to join a session without being invited. For example, the chairman of a video chat may want to leave the door of their meeting open for newcomers. The receiver-initiated join model can be implemented, if desired, by introducing a server that hosts can talk to to join a conference. 8. Optional information 8.1. List of ports Although an extension to SIP could be arranged such that all participants in a session use the same transport (UDP) port number, Ooms, et al. Expires December 2004 [Page 14] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 in the general case it is possible for each participant to listen on a different port number. To cover this case, the Xcast packet optionally contains a list of port numbers. If the list of port numbers is present, the destination port number in the transport layer header will be set to zero. On X2U the destination port number in the transport layer header will be set to the port number corresponding to the destination of the unicast packet. 8.2. List of DSCPs The Xcast packet could (optionally) also contain a list of DiffServ CodePoints (DSCPs). While traditional multicast protocols have to create separate groups for each service class, Xcast incorporates the possibility of having receivers with different service requirements within one channel. The DSCP in the IP header will be set to the most demanding DSCP of the list of DSCPs. This DSCP in the IP header will determine e.g. the scheduler to use. If two destinations, with the same next-hop, have 'non-mergable' DSCPs, two Xcast packets will be created. 'Non-mergable' meaning that one can not say that one is more or less stringent than the other. 8.3. Channel Identifier Optionally a sender can decide to add an extra number in the Xcast header: the Channel Identifier. If the source does not want to use this option it MUST set the Channel Identifier to zero. If the Channel Identifier is non-zero the pair (Source Address, Channel Identifier) MUST uniquely identify the channel (note that this is similar to the (S, G) pair in SSM). This document does not assign any other semantics to the Channel Identifier besides the one above. This Channel Identifier could be useful for several purposes: 1) An identifier of the channel in error, flow control, etc. messages 2) A key to a caching table [OOMS]. 3) It gives an extra de-multiplexing possibility (beside the port- number) 4) ... 9. Encoding Ooms, et al. Expires December 2004 [Page 15] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 9.1. General The source address field of the IP header contains the address of the Xcast sender. The destination address field carries the All-Xcast- Routers address (to be assigned link-local multicast address), this is to have a fixed value. Every Xcast router joins this multicast group. The reasons for putting a fixed number in the destination field are: 1) The destination address field is part of the IP pseudo header and the latter is covered by transport layer checksums (e.g. UDP checksum). So the fixed value avoids a (delta) recalculation of the checksum. 2) The IPsec AH covers the IP header destination address hence preventing any modification to that field. Also, both AH and ESP payloads cover the whole UDP packet (via authentication and/or encryption). The UDP checksum cannot therefore be updated if the IP header destination address were to change. 3) In Xcast for IPv6 the Routing Extension shall be used, this header extension is only checked by a router if the packet is destined to this router. This is achieved by making all Xcast routers part of the All_Xcast_Routers group. 4) Normally Xcast packets are only visible to Xcast routers. However, if a non-Xcast router receives an Xcast packet by accident (or by criminal intent), it will not send ICMP errors since the Xcast packet carries a multicast address in the destination address field ([1812]). Note that some benefits only hold when the multicast address stays in the destination field until it reaches the end-node (thus not combinable with X2U). 9.2. IPv4 [AGUI] and [1770] proposed (for a slightly different purpose) to carry multiple destinations in the IPv4 option. But because of the limited flexibility (limited size of the header), Xcast will follow another approach. The list of destinations will be encoded in a separate header. The Xcast header for IPv4 (in short Xcast4) is carried between the IPv4 header and the transport layer header. [IPv4 header | Xcast4 | transport header | payload ] Note also that since the Xcast header is added to the data portion of the packet, if the sender wishes to avoid IP fragmentation, it must Ooms, et al. Expires December 2004 [Page 16] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 take the size of the Xcast header into account. 9.2.1. IPv4 header The Xcast4 header is carried on top of an IP header. The IP header will carry the protocol number PROTO_Xcast. The source address field contains the address of the Xcast sender. The destination address field carries the All_Xcast_Routers address. 9.2.2. Xcast4 header The Xcast4 header is depicted in Figure 4. It is composed of two parts: a fixed part (first 12 octets) and two variable length parts that are specified by the fixed part. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |VERSION|A|X|D|P|R| NBR_OF_DEST | CHECKSUM | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CHANNEL IDENTIFIER | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PROT ID | LENGTH | RESV | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List of Addresses and DSCPs | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List of Port Numbers (optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4 VERSION = Xcast version number. This document describes version 1. A = Anonymity bit: if this bit is set the destination addresses for which the corresponding bit in the bitmap is zero must be overwritten by zero. X = Xcast bit: if this bit is set a router MUST NOT reduce the Xcast packet to unicast packet(s), i.e. the packet MUST stay an Xcast packet end-to-end. This bit can be useful when IPsec is applied. If this bit is cleared a router SHOULD apply X2U if there is only one destination left in the Xcast packet. In some cases a router could decide not to apply X2U to a packet with the Xcast bit cleared, e.g. the router has no directly connected hosts and wants to avoid the extra processing required by X2U. D = DSCP bit: if this bit is set the packet will contain a DS-byte Ooms, et al. Expires December 2004 [Page 17] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 for each destination. P = Port bit: if this bit is set the packet will contain a port number for each destination. NBR_OF_DEST = the number of original destinations. CHECKSUM = A checksum on the Xcast header only. This is verified and recomputed at each point that the Xcast header is processed. The checksum field is the 16 bit one's complement of the one's complement sum of all the bytes in the header. For purposes of computing the checksum, the value of the checksum field is zero. It is not clear yet whether a checksum is needed (ffs). If only one destination is wrong it can still be useful to forward the packet to N-1 correct destinations and 1 incorrect destination. CHANNEL IDENTIFIER = 4 octets Channel Identifier (see section 8.3). Since it is located within the first 8 bytes of the header, it will be returned in ICMP messages. PROT ID = specifies the protocol of the following header. LENGTH = length of the Xcast header in 4-octet words. This field puts an upper boundary to the number of destinations. This value is also determined by the NBR_OF_DEST field and the D and P bits. RESV = R = Reserved. It must be zero on transmission and must be ignored on receipt. The first variable part is the 'List of Addresses and DSCPs', the second variable part is the 'List of Port Numbers'. Both are 4-octet aligned. The second variable part is only present if the P-bit is set. Figure 5 gives an example of the variable part for the case that the P-bit is set and the D-bit is cleared (in this example N is odd): Ooms, et al. Expires December 2004 [Page 18] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | BITMAP | ~ ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ... ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination N | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port 1 | Port 2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ... ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Port N | padding | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5 BITMAP = every destination has a corresponding bit in the bitmap to indicate whether the destination is still valid on this branch of the tree. The first bit corresponds to the first destination in the list. This field is 4-octet aligned (e.g. for 49 destinations there will be a 64-bit bitmap). If Xcast is applied in combination with IPsec, the bitmap - since it can change on route - has to be moved to a new to be defined IPv4 option. List of Destinations. Each address size is four octets. List of Port Numbers. List of two octet destination port number(s), where each port corresponds in placement to the preceding Destination Address. 9.3. IPv6 The Xcast6 header encoding is similar to IPv4, except that Xcast information is stored in IPv6 extension headers. [IPv6 header | Xcast6 | transport header | payload ] 9.3.1. IPv6 header The IPv6 header will carry the NextHeader value 'Routing Extension'. The source address field contains the address of the Xcast sender. The destination address field carries the All_Xcast_Routers address. Ooms, et al. Expires December 2004 [Page 19] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 9.3.2. Xcast6 header The Xcast6 header is also composed of a fixed and two variable parts. The fixed and the first variable part is carried in a Routing Extension. The second variable part is carried in a Destination Extension. 9.3.2.1. Routing Extension header The P-bit of Xcast4 is not present because it is implicit by the presence or absence of the Destination Extension (Figure 6). 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next Header | HdrExtLen |RouteType=Xcast| 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |VERSION|A|X|D| R | NBR_OF_DEST | CHECKSUM | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CHANNEL IDENTIFIER | ~ ~ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List of Addresses and DSCPs | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 6 HdrExtLen = The header length is expressed in 8-octets, thus a maximum of 127 destinations can be listed (this is why NBR_OF_DEST is 7-bit). RouteType = Xcast should be assigned by IANA. The fourth octet is set to 0. R = Reserved. CHANNEL IDENTIFIER = 16 octets Channel Identifier (see section 8.3). The other fields are defined in section 9.2.2. The 'List of Addresses and DSCPs' is 8-octet aligned. The size of the bitmap is determined by the number of destinations and is a multiple of 64 bits. 9.3.2.2. Destination Extension header Optionally the Destination Extension (Figure 7) is present to specify Ooms, et al. Expires December 2004 [Page 20] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 the list of Port Numbers. The destination header is only evaluated by the destination node. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next Header | HdrExtLen |Opt Type=Ports | Opt Data Len | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | List of Port Numbers | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7 Option Type for Ports should be assigned by IANA. The first three bits MUST be 010 to indicate that the packet must be discarded if the option is unknown and that the option can not be changed en-route. The number of Ports MUST be equal to the number of destinations specified in the Routing header. 10. Impact on Upper Layer Protocols Some fields in the Xcast header(s) can be modified as the packet travels along its delivery path. This has an impact on: 10.1. Checksum calculation in transport layer headers In transport layer headers, the target of the checksum calculation includes the IP pseudo header, transport header and payload (IPv6 header extensions are not a target). The transformation of an Xcast packet to a normal unicast packet - (premature) X2U - replaces the multicast address in the IP header destination field by the address of a final destination. If the Xcast header contains a Port List, the port number in the transport layer (which should be zero) also needs to be replaced by the port number corresponding to the destination. This requires a recalculation of these checksums. Note that this does not require a complete recalculation of the checksum, only a delta calculation, e.g. for IPv4: Checksum' = ~ (~Checksum + ~daH + ~daL + daH' + daL' + ~dp + dp') In which "'" indicates the new values, "da" the destination address, "dp" the destination port and "H" and "L" respectively the higher and lower 16 bit. Ooms, et al. Expires December 2004 [Page 21] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 10.2. IPsec This is described in [PARI]. 11. Gradual Deployment 11.1. Tunneling One way to deploy Xcast in a network that has routers that have no knowledge of Xcast is to setup "tunnels" between Xcast peers (MBone approach). This enables the creation of a virtual network layered on top of an existing network [2003]. The Xcast routers exchange and maintain Xcast routing information via any standard unicast routing protocol (e.g. RIP, OSPF, ISIS). The Xcast routing table that is created is simply a standard unicast routing table that contains the destinations that have Xcast connectivity, along with their corresponding Xcast next hops. In this way, packets may be forwarded hop-by-hop to other Xcast routers, or may be "tunneled" through non- Xcast routers in the network. For example, suppose that A is trying to get packets distributed to B, C & D in Figure 8 below, where "X" routers are Xcast-capable, and "R" routers are not. Figure 9 shows the routing tables created via the Xcast tunnels: R4 ---- B / / A ----- X1 ---- R2 ---- X3 R8 ---- C \ / \ / R5 ---- R6 ---- X7 \ \ R9 ---- D Figure 8 Router X1 establishes a tunnel to Xcast peer X3. Router X3 establishes a tunnel to Xcast peers X1 and X7. Router X7 establishes a tunnel to Xcast peer X3. Ooms, et al. Expires December 2004 [Page 22] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 X1 routing table: X3 routing table: X7 routing table: Dest | NextHop Dest | NextHop Dest | NextHop ------+---------- ------+--------- ------+--------- B | X3 A | X1 A | X3 C | X3 C | X7 B | X3 D | X3 D | X7 Figure 9 The source A will send an Xcast packet to its default Xcast router, X1, that includes the list of destinations for the packet. The packet on the link between X1 and X3 is depicted in Figure 10: +----------+ | payload | +----------+ | UDP | +----------+ | Xcast | | B,C,D | | prot=UDP | +----------+ | inner IP | | src=A | |dst=All_X_| |prot=Xcast| +----------+ | outer IP | | src=X1 | | dst=X3 | | prot=IP | +----------+ Figure 10 When X3 receives this packet, it processes it as follows: - Perform a route table lookup in the Xcast routing table to determine the Xcast next hop for each of the destinations listed in the packet. - If no Xcast next hop is found, replicate the packet and send a standard unicast to the destination. - For those destinations for which an Xcast next hop is found, partition the destinations based on their next hops. - Replicate the packet so that there's one copy of the packet for each of the Xcast next hops found in the previous steps. Ooms, et al. Expires December 2004 [Page 23] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 - Modify the list of destinations in each of the copies so that the list in the copy for a given next hop includes just the destinations that ought to be routed through that next hop. - Send the modified copies of the packet on to the next hops. - Optimization: If there is only one destination for a particular Xcast next hop, send the packet as a standard unicast packet to the destination, since there is no advantage to forwarding it as an Xcast packet. So, in the example above, X1 will send a single packet on to X3 with a destination list of < B C D >. This packet will be received by R2 as a unicast packet with destination X3, and R2 will forward it on, having no knowledge of Xcast. When X3 receives the packet, it will, by the algorithm above, send one copy of the packet to destination < B > as an ordinary unicast packet, and 1 copy of the packet to X7 with a destination list of < C D >. R4, R5, and R6 will behave as standard routers with no knowledge of Xcast. When X7 receives the packet, it will parse the packet and transmit ordinary unicast packets addressed to < C > and < D > respectively. 11.2. Premature X2U If a router discovers that its downstream neighbor is not Xcast capable, it can perform a Premature X2U, i.e. send a unicast packet for each destination in the Xcast header which has this neighbor as a next hop. Thus duplication is done before the Xcast packet reached its actual branching point. A mechanism (protocol/protocol extension) to discover the Xcast capability of a neighbor is ffs. Among others, one could think of an extension to a routing protocol to advertise Xcast capabilities or one could send periodic 'Xcast pings' to its neighbors (send an Xcast packet that contains its own address as a destination and check whether the packet returns). 11.3. Semi-permeable tunneling (IPv6 only) This is an optimization of tunneling in the sense that it does not require (manual) configuration of tunnels. It is enabled by adding a Hop-by-Hop Xcast6 header. An IPv6 packet can initiate/trigger additional processing in the on-route routers by using the IPv6 Hop- by-hop option. The type of the Xcast6 Hop-by-hop option has a prefix '00' so that routers that cannot recognize Xcast6 can treat the Xcast6 datagram as a normal IPv6 datagram and forward toward the destination in the IPv6 Ooms, et al. Expires December 2004 [Page 24] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 header. Packets will be delivered to all members if at least all participating hosts are upgraded. When the source A sends an Xcast packet via semi-permeable tunneling to destinations B, C and D it will create the packet of Figure 11. One of the final destinations will be put in the destination address field of the outer IP header. +----------+ | payload | +----------+ | UDP | +----------+ | Xcast | | | +----------+ | inner IP | | src=A | |dst=All_X_| |prot=Xcast| +----------+ | Xcast | |SP-tunnel | |Hop-by-hop| +----------+ | outer IP | | src=A | | dst=B | | prot=IP | +----------+ Figure 11 Semi-permeable tunneling is a special tunneling technology that permits intermediate Xcast routers on a tunnel to check the destinations and branch if destinations have a different next hop. Note that with the introduction of an Xcast IPv4 option, this technique could also be applied in IPv4 networks. 11.4. Special case: deployment without network support A special method of deploying Xcast is possible by upgrading only the hosts. By applying tunneling (see section 11.1 and 11.3) with one of the final destinations as tunnel endpoint, the Xcast packet will be delivered to all destinations when all the hosts are Xcast aware. Both normal and semi-permeable tunneling can be used. Ooms, et al. Expires December 2004 [Page 25] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 If host B receives this packet, in the above example, it will notice the other destinations in the Xcast header. B will create a new Xcast packet and will send it to one of the remaining destinations. In the case of Xcast6 and semi-permeable tunneling, Xcast routers can be introduced in the network without the need of configuring tunnels. The disadvantages of this method are that: - all hosts in the session need to be upgraded. - non-optimal routing. - anonymity issue: hosts can know the identity of other parties in the session (which is not a big issue in conferencing, but maybe for some other application?). - host has to perform network functions and needs an upstream link which has the same bandwidth as its downstream link. 11.5 Using a Small Number of Xcast-Aware Routers to Provide Xcast in a Not-so-Small Network In this approach, an xcast packet uses a special 32-bit unicast address in the destination field of the IP header. In the simplest version of this scheme, there might be only a single xcast-aware router in a network. This xcast-aware router looks like a "server" to the other routers and it is configured so that its IP address (or one of its IP addresses) corresponds to the "special" 32-bit address. Thus when xcast clients send xcast packets, the non-xcast-aware routers will route these packets to the xcast-aware router and the xcast-aware router can "explode" (X2U) them into an appropriate set of unicast packets. This allows clients anywhere in a network to use xcast to overcome the problem of limited bandwidth in the "first mile" with a minimum number of xcast-aware routers (i.e. 1). Another possibility is to deploy a few of these xcast-aware routers at various points in the network and configure each of these with the special 32-bit address. This provides redundancy, eliminating the single point of failure, and reduces the distance an xcast packet needs to travel to reach an xcast-aware router, reducing network latencies. In this case, the xcast-aware routers appear to be a single server that is "multihomed" (i.e. connected to the network at more than one place) and the non-xcast-aware routers will, via ordinary unicast routing, deliver packets that are addressed to this "multihomed virtual server" via the shortest available path. (Note that this scheme of delivering packets to any host in a group Ooms, et al. Expires December 2004 [Page 26] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 is also known as an "anycast" and is described in more detail in RFC's 1546, 2526 and 3068. Note too that RFC 1546 says: The important observation is that multiple routes to an anycast address appear to a router as multiple routes to a unicast destination, and the router can use standard algorithms to choose the best route.) 12. (Socket) API In the most simple use of Xcast, the final destinations of an Xcast packet receive an ordinary unicast UDP packet. This means that hosts can receive an Xcast packet with a standard, unmodified TCP/IP stack. Hosts can also transmit Xcast packets with a standard TCP/IP stack with a small Xcast library that sends Xcast packets on a raw socket. This has been used to implement Xcast based applications on both Unix and Windows platforms without any kernel changes. Another possibility is to modify the sockets interface slightly. For example, one might add an "xcast_sendto" function that works like "sendto" but that uses a list of destination addresses in place of the single address that "sendto" uses. 13. Security Considerations See [PARI]. References [1075] D. Waitzman, C. Partridge, S.E. Deering, Distance Vector Multi- cast Routing Protocol, RFC 1075, November 1988. [1770] C. Graff, "IPv4 Option for Sender Directed Multi-Destination Delivery", RFC1770, March 1995. [1812] F. Baker, "Requirements for IP Version 4 Routers", RFC1812, June 1995. [2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, October 1996. [2201] A. Ballardie, Core Based Trees (CBT) Multicast Routing Architec- ture, RFC 2201, Sept. 1997. Ooms, et al. Expires December 2004 [Page 27] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 [2236] W. Fenner, Internet Group Management Protocol, Version 2, RFC 2236, Nov. 1997. [2401] S. Kent, R. Atkinson, "Security Architecture for the Internet Protocol", RFC2401, November 1998. [2460] S. Deering, R. Hinden. Internet Protocol, Version 6 (IPv6), RFC2460, December 1998. [2543] M. Handley, H. Schulzrinne, E. Schooler, J, Rosenberg, "SIP: Session Initiation Protocol", RFC2543, March 1999. [2902] S. Deering, S. Hares, C. Perkins, R. Perlman, "Overview of the 1998 IAB Routing Workshop", RFC2902, August 2000. [AGUI] L. Aguilar, "Datagram Routing for Internet Multicasting", Sig- comm84, March 1984. [BOIV] R. Boivie, N. Feldman, "Small Group Multicast", draft-boivie- sgm-01.txt, July 2000. [DEER] S. Deering, "Multicast Routing in a datagram internetwork", PhD thesis, December 1991. [DEE2] S. Deering, D. Estrin, D. Farinacci, V. Jacobson, C. Liu, and L. Wei. The Pim Architecture for Wide-area Multicast Routing, ACM Transactions on Networks, April 1996 [DOOR] B. Van Doorselaer, D. Ooms, "SIP for the establishment of xcast- based multiparty conferences", draft-van-doorselaer-sip- xcast-00.txt, July 2000. [FARI] D. Farinacci, "Multicast Source Discovery Protocol", draft-fari- nacci-msdp-00.txt, June 1998. [H323] ITU-T Recommendation H.323 (2000), Packet-Based Multimedia Com- munications Systems. [HOLB] H. Holbrook, B. Cain, "Source-Specific Multicast for IP", draft- holbrook-ssm-00.txt, March 2000. [IMAI] Y. Imai, Multiple Destination option on IPv6 (MDO6), , September 2000 [MBONE] Frequently Asked Questions (FAQ) on the Multicast Backbone (MBONE), ftp://venera.isi.edu/mbone/faq.txt Ooms, et al. Expires December 2004 [Page 28] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 [OOMS] D. Ooms, W. Livens, Connectionless Multicast, , April 2000 [PARI] O. Paridaens, D. Ooms, Security Framework for Explicit Multi- cast, draft-paridaens-xcast-sec-framework-01.txt, November 2000. [PERL] R. Perlman, "Simple Multicast: A design for Simple, Low-overhead Multicast", draft-perlman-simple-multicast-02.txt, February 1999. [RMT] Reliable Multicast Transport Working Group web site, http://www.ietf.org/html.charters/rmt-charter.html, June 15, 1999 [SOLA] M. Sola, M. Ohta, T. Maeno. Scalability of Internet Multicast Protocols, INET'98, http://www.isoc.org/inet98/proceed- ings/6d/6d_3.htm Authors Addresses Rick Boivie IBM T. J. Watson Research Center 19 Skyline Drive Hawthorne, NY 10532 Phone: 914-784-3251 Email: rhboivie@us.ibm.com Nancy Feldman IBM T. J. Watson Research Center 19 Skyline Drive Hawthorne, NY 10532 Email: nkfeldman@yahoo.com Yuji Imai Fujitsu LABORATORIES Ltd. 1-1, Kamikodanaka 4-Chome, Nakahara-ku, Kawasaki 211-8588, Japan Phone : +81-44-754-2628 Fax : +81-44-754-2793 E-mail: kimai@flab.fujitsu.co.jp Wim Livens Colt Telecom Zweefvliegtuigstraat 10, 1130 Brussel, Belgium. Phone : 32 2 7901705 Fax : 32 2 7901711 E-mail: WLivens@colt-telecom.be Ooms, et al. Expires December 2004 [Page 29] Internet Draft draft-ooms-xcast-basic-spec-06.txt June 2004 Dirk Ooms OneSparrow Belegstraat 13; 2018 Antwerp; Belgium E-mail: dirk@onesparrow.com Olivier Paridaens Alcatel Network Strategy Group Fr. Wellesplein 1, 2018 Antwerpen, Belgium. Phone : 32 3 2409320 E-mail: Olivier.Paridaens@alcatel.be Eiichi Muramoto Matsushita Electric Industrial Co., Ltd. 4-5-15 Higashi-shinagawa, Shinagawa-ku, Tokyo 140-8632, Japan Phone : +81-3-5460-2734 E-mail: muramoto.eiichi@jp.panasonic.com Ooms, et al. Expires December 2004 [Page 30]