Network Working Group C. Lonvick, Ed. Internet-Draft Cisco Systems, Inc Expires: April 24, 2005 October 24, 2004 SSH Protocol Assigned Numbers draft-ietf-secsh-assignednumbers-07.txt Status of this Memo This document is an Internet-Draft and is subject to all provisions of section 3 of RFC 3667. By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she become aware will be disclosed, in accordance with RFC 3668. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on April 24, 2005. Copyright Notice Copyright (C) The Internet Society (2004). Abstract This document defines the instructions to the IANA and the initial state of the IANA assigned numbers for the SSH protocol. It is intended only for the initialization of the IANA registries referenced in the documents. Lonvick Expires April 24, 2005 [Page 1] Internet-Draft SSH Protocol Assigned Numbers October 2004 Table of Contents 1. Editor's Note . . . . . . . . . . . . . . . . . . . . . . . 3 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 3. Conventions Used in This Document . . . . . . . . . . . . . 3 4. IANA Considerations . . . . . . . . . . . . . . . . . . . . 4 4.1 Message Numbers . . . . . . . . . . . . . . . . . . . . . 4 4.1.1 Conventions . . . . . . . . . . . . . . . . . . . . . 4 4.1.2 Initial Assignments . . . . . . . . . . . . . . . . . 5 4.1.3 Future Assignments . . . . . . . . . . . . . . . . . . 6 4.2 Disconnection Messages Reason Codes and Descriptions . . . 6 4.2.1 Conventions . . . . . . . . . . . . . . . . . . . . . 6 4.2.2 Initial Assignments . . . . . . . . . . . . . . . . . 6 4.2.3 Future Assignments . . . . . . . . . . . . . . . . . . 7 4.3 Channel Connection Failure Reason Codes and Descriptions . 7 4.3.1 Conventions . . . . . . . . . . . . . . . . . . . . . 7 4.3.2 Initial Assignments . . . . . . . . . . . . . . . . . 7 4.3.3 Future Assignments . . . . . . . . . . . . . . . . . . 7 4.4 Extended Channel Data Transfer data_type_code and Data . . 8 4.4.1 Conventions . . . . . . . . . . . . . . . . . . . . . 8 4.4.2 Initial Assignments . . . . . . . . . . . . . . . . . 8 4.4.3 Future Assignments . . . . . . . . . . . . . . . . . . 8 4.5 Pseudo-Terminal Encoded Terminal Modes . . . . . . . . . . 8 4.5.1 Conventions . . . . . . . . . . . . . . . . . . . . . 9 4.5.2 Initial Assignments . . . . . . . . . . . . . . . . . 9 4.5.3 Future Assignments . . . . . . . . . . . . . . . . . . 10 4.6 Names . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.6.1 Conventions for Names . . . . . . . . . . . . . . . . 11 4.6.2 Future Assignments of Names . . . . . . . . . . . . . 11 4.7 Service Names . . . . . . . . . . . . . . . . . . . . . . 11 4.8 Authentication Method Names . . . . . . . . . . . . . . . 12 4.9 Connection Protocol Assigned Names . . . . . . . . . . . . 12 4.9.1 Connection Protocol Channel Types . . . . . . . . . . 12 4.9.2 Connection Protocol Global Request Names . . . . . . . 12 4.9.3 Connection Protocol Channel Request Names . . . . . . 12 4.9.4 Initial Assignment of Signal Names . . . . . . . . . . 13 4.10 Key Exchange Method Names . . . . . . . . . . . . . . . 13 4.11 Assigned Algorithm Names . . . . . . . . . . . . . . . . 13 4.11.1 Encryption Algorithm Names . . . . . . . . . . . . . 14 4.11.2 MAC Algorithm Names . . . . . . . . . . . . . . . . 14 4.11.3 Public Key Algorithm Names . . . . . . . . . . . . . 14 4.11.4 Compression Algorithm Names . . . . . . . . . . . . 15 5. References . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.1 Normative References . . . . . . . . . . . . . . . . . . . . 15 5.2 Informative References . . . . . . . . . . . . . . . . . . . 16 Author's Address . . . . . . . . . . . . . . . . . . . . . . 16 Intellectual Property and Copyright Statements . . . . . . . 17 Lonvick Expires April 24, 2005 [Page 2] Internet-Draft SSH Protocol Assigned Numbers October 2004 1. Editor's Note The references in this document are statically defined. However, the locations of the referenced materials are dynamic and are changing with the whims of the Working Group. Please do not comment to the editor or the Working Group about inaccuracies along those lines in this document at this time. (This paragraph will be removed before this document is submitted to the RFC Editor.) 2. Introduction This document does not define any new protocols. It is intended only to create the initial state of the IANA databases for the SSH protocol and also contains instructions for future assignments. Except for one HISTORIC algorithm generally regarded as obsolete, this document does not define any new protocols or any number ranges not already defined in: [SSH-ARCH], [SSH-TRANS], [SSH-USERAUTH], [SSH-CONNECT]. 3. Conventions Used in This Document The keywords "MUST", "MUST NOT", "REQUIRED", "SHOULD", "SHOULD NOT", and "MAY" that appear in this document are to be interpreted as described in [RFC2119]. The keywords "PRIVATE USE", "HIERARCHICAL ALLOCATION", "FIRST COME FIRST SERVED", "EXPERT REVIEW", "SPECIFICATION REQUIRED", "IESG APPROVAL", "IETF CONSENSUS", and "STANDARDS ACTION" that appear in this document when used to describe namespace allocation are to be interpreted as described in [RFC2434]. These designations are repeated in this document for clarity. PRIVATE USE - For private or local use only, with the type and purpose defined by the local site. No attempt is made to prevent multiple sites from using the same value in different (and incompatible) ways. There is no need for IANA to review such assignments and assignments are not generally useful for interoperability. HIERARCHICAL ALLOCATION - Delegated managers can assign values provided they have been given control over that part of the name space. IANA controls the higher levels of the namespace according to one of the other policies. FIRST COME FIRST SERVED - Anyone can obtain an assigned number, so long as they provide a point of contact and a brief description of what the value would be used for. For numbers, the exact value is generally assigned by the IANA; with names, specific names are Lonvick Expires April 24, 2005 [Page 3] Internet-Draft SSH Protocol Assigned Numbers October 2004 usually requested. EXPERT REVIEW - approval by a Designated Expert is required. SPECIFICATION REQUIRED - Values and their meaning must be documented in an RFC or other permanent and readily available reference, in sufficient detail so that interoperability between independent implementations is possible. IESG APPROVAL - New assignments must be approved by the IESG, but there is no requirement that the request be documented in an RFC (though the IESG has discretion to request documents or other supporting materials on a case-by-case basis). IETF CONSENSUS - New values are assigned through the IETF consensus process. Specifically, new assignments are made via RFCs approved by the IESG. Typically, the IESG will seek input on prospective assignments from appropriate persons (e.g., a relevant Working Group if one exists). STANDARDS ACTION - Values are assigned only for Standards Track RFCs approved by the IESG. 4. IANA Considerations This entire document is the IANA considerations for the SSH protocol as is defined in [SSH-ARCH], [SSH-TRANS], [SSH-USERAUTH], [SSH-CONNECT]. This section contains conventions used in naming the namespaces, the initial state of the registry, and instructions for future assignments. 4.1 Message Numbers The Message Number is an 8-bit value, which describes the payload of a packet. 4.1.1 Conventions Protocol packets have message numbers in the range 1 to 255. These numbers are allocated as follows: Transport layer protocol: 1 to 19 Transport layer generic (e.g. disconnect, ignore, debug, etc.) 20 to 29 Algorithm negotiation 30 to 49 Key exchange method specific (numbers can be reused Lonvick Expires April 24, 2005 [Page 4] Internet-Draft SSH Protocol Assigned Numbers October 2004 for different authentication methods) User authentication protocol: 50 to 59 User authentication generic 60 to 79 User authentication method specific (numbers can be reused for different authentication methods) Connection protocol: 80 to 89 Connection protocol generic 90 to 127 Channel related messages Reserved for client protocols: 128 to 191 Reserved Local extensions: 192 to 255 Local extensions 4.1.2 Initial Assignments Message ID Value Reference ----------- ----- --------- SSH_MSG_DISCONNECT 1 [SSH-TRANS] SSH_MSG_IGNORE 2 [SSH-TRANS] SSH_MSG_UNIMPLEMENTED 3 [SSH-TRANS] SSH_MSG_DEBUG 4 [SSH-TRANS] SSH_MSG_SERVICE_REQUEST 5 [SSH-TRANS] SSH_MSG_SERVICE_ACCEPT 6 [SSH-TRANS] SSH_MSG_KEXINIT 20 [SSH-TRANS] SSH_MSG_NEWKEYS 21 [SSH-TRANS] SSH_MSG_KEXDH_INIT 30 [SSH-TRANS] SSH_MSG_KEXDH_REPLY 31 [SSH-TRANS] SSH_MSG_USERAUTH_REQUEST 50 [SSH-USERAUTH] SSH_MSG_USERAUTH_FAILURE 51 [SSH-USERAUTH] SSH_MSG_USERAUTH_SUCCESS 52 [SSH-USERAUTH] SSH_MSG_USERAUTH_BANNER 53 [SSH-USERAUTH] SSH_MSG_USERAUTH_PK_OK 60 [SSH-USERAUTH] SSH_MSG_GLOBAL_REQUEST 80 [SSH-CONNECT] SSH_MSG_REQUEST_SUCCESS 81 [SSH-CONNECT] SSH_MSG_REQUEST_FAILURE 82 [SSH-CONNECT] SSH_MSG_CHANNEL_OPEN 90 [SSH-CONNECT] SSH_MSG_CHANNEL_OPEN_CONFIRMATION 91 [SSH-CONNECT] SSH_MSG_CHANNEL_OPEN_FAILURE 92 [SSH-CONNECT] Lonvick Expires April 24, 2005 [Page 5] Internet-Draft SSH Protocol Assigned Numbers October 2004 SSH_MSG_CHANNEL_WINDOW_ADJUST 93 [SSH-CONNECT] SSH_MSG_CHANNEL_DATA 94 [SSH-CONNECT] SSH_MSG_CHANNEL_EXTENDED_DATA 95 [SSH-CONNECT] SSH_MSG_CHANNEL_EOF 96 [SSH-CONNECT] SSH_MSG_CHANNEL_CLOSE 97 [SSH-CONNECT] SSH_MSG_CHANNEL_REQUEST 98 [SSH-CONNECT] SSH_MSG_CHANNEL_SUCCESS 99 [SSH-CONNECT] SSH_MSG_CHANNEL_FAILURE 100 [SSH-CONNECT] 4.1.3 Future Assignments Requests for assignments of new message numbers in the range of 1 to 127 MUST be done through the STANDARDS ACTION method as described in [RFC2434]. Requests for assigments of new message numbers in the range of 128 to 191 MUST be done through the IETF CONSENSUS method as described in [RFC2434]. The IANA will not control the message numbers range of 192 through 255. This range will be left for PRIVATE USE. 4.2 Disconnection Messages Reason Codes and Descriptions The Disconnection Message 'reason code' is a uint32 value. The associated Disconnection Message 'description string' is a human-readable message which describes the disconnect reason. 4.2.1 Conventions Protocol packets containing the SSH_MSG_DISCONNECT message MUST have Disconnection Message 'reason code' values in the range of 0x00000001 to 0xFFFFFFFF. 4.2.2 Initial Assignments description string reason Reference code ------------------ ----- --------- SSH_DISCONNECT_HOST_NOT_ALLOWED_TO_CONNECT 1 [SSH-TRANS] SSH_DISCONNECT_PROTOCOL_ERROR 2 [SSH-TRANS] SSH_DISCONNECT_KEY_EXCHANGE_FAILED 3 [SSH-TRANS] SSH_DISCONNECT_RESERVED 4 [SSH-TRANS] SSH_DISCONNECT_MAC_ERROR 5 [SSH-TRANS] SSH_DISCONNECT_COMPRESSION_ERROR 6 [SSH-TRANS] SSH_DISCONNECT_SERVICE_NOT_AVAILABLE 7 [SSH-TRANS] SSH_DISCONNECT_PROTOCOL_VERSION_NOT_SUPPORTED 8 [SSH-TRANS] Lonvick Expires April 24, 2005 [Page 6] Internet-Draft SSH Protocol Assigned Numbers October 2004 SSH_DISCONNECT_HOST_KEY_NOT_VERIFIABLE 9 [SSH-TRANS] SSH_DISCONNECT_CONNECTION_LOST 10 [SSH-TRANS] SSH_DISCONNECT_BY_APPLICATION 11 [SSH-TRANS] SSH_DISCONNECT_TOO_MANY_CONNECTIONS 12 [SSH-TRANS] SSH_DISCONNECT_AUTH_CANCELLED_BY_USER 13 [SSH-TRANS] SSH_DISCONNECT_NO_MORE_AUTH_METHODS_AVAILABLE 14 [SSH-TRANS] SSH_DISCONNECT_ILLEGAL_USER_NAME 15 [SSH-TRANS] 4.2.3 Future Assignments Disconnection Message 'reason code' values MUST be assigned sequentially. Requests for assignments of new Disconnection Message 'reason codes', and their associated Disconnection Message 'description string', in the range of 0x00000010 through 0xFFFFFFE9 MUST be done through the IETF CONSENSUS method as described in [RFC2434]. The IANA will not assign Disconnection Message 'reason codes' in the range of 0xFFFFFFF0 through 0xFFFFFFFF. Disconnection Message 'reason code' values in that range are left for PRIVATE USE as described in [RFC2434]. 4.3 Channel Connection Failure Reason Codes and Descriptions The Channel Connection Failure 'reason code' is a uint32 value. The associated Channel Connection Failure 'description string' is a human-readable message which describes the channel connection failure reason. 4.3.1 Conventions Protocol packets containing the SSH_MSG_CHANNEL_OPEN_FAILURE message MUST have Channel Connection Failure 'reason code' values in the range of 0x00000001 to 0xFFFFFFFF. 4.3.2 Initial Assignments description string reason Reference code ------------------ ----- --------- SSH_OPEN_ADMINISTRATIVELY_PROHIBITED 1 [SSH-CONNECT] SSH_OPEN_CONNECT_FAILED 2 [SSH-CONNECT] SSH_OPEN_UNKNOWN_CHANNEL_TYPE 3 [SSH-CONNECT] SSH_OPEN_RESOURCE_SHORTAGE 4 [SSH-CONNECT] 4.3.3 Future Assignments Channel Connection Failure 'reason code' values MUST be assigned Lonvick Expires April 24, 2005 [Page 7] Internet-Draft SSH Protocol Assigned Numbers October 2004 sequentially. Requests for assignments of new Channel Connection Failure 'reason code' values, and their associated Channel Connection Failure 'description string', in the range of 0x00000005 to 0xFFFFFFE9 MUST be done through the IETF CONSENSUS method as described in [RFC2434]. The IANA will not assign Channel Connection Failure 'reason code' values in the range of 0xFFFFFFF0 to 0xFFFFFFFF. Channel Connection Failure 'reason code' values in that range are left for PRIVATE USE as described in [RFC2434]. 4.4 Extended Channel Data Transfer data_type_code and Data The Extended Channel Data Transfer 'data_type_code' is an uint23 value. The associated Extended Channel Data Transfer 'data' is a human-readable message which describes the type of data allowed to be transferred in the channel. 4.4.1 Conventions Protocol packets containing the SSH_MSG_CHANNEL_EXTENDED_DATA message MUST have Extended Channel Data Transfer 'data_type_code' values in the range of 0x00000001 to 0xFFFFFFFF. 4.4.2 Initial Assignments data data_type_code Reference ---- -------------- --------- SSH_EXTENDED_DATA_STDERR 1 [SSH-CONNECT] 4.4.3 Future Assignments Extended Channel Data Transfer 'data_type_code' values MUST be assigned sequentially. Requests for assignments of new Extended Channel Data Transfer 'data_type_code' values, and their associated Extended Channel Data Transfer 'data' strings, in the range of 0x00000002 to 0xFFFFFFE9 MUST be done through the IETF CONSENSUS method as described in [RFC2434]. The IANA will not assign Extended Channel Data Transfer 'data_type_code' values in the range of 0xFFFFFFF0 to 0xFFFFFFFF. Extended Channel Data Transfer 'data_type_code' values in that range are left for PRIVATE USE as described in [RFC2434]. 4.5 Pseudo-Terminal Encoded Terminal Modes SSH_MSG_CHANNEL_REQUEST messages with a "pty-req" string MUST contain "encoded terminal modes". These "encoded terminal modes" are opcode-argument pairs consisting of an opcode and an argument. Lonvick Expires April 24, 2005 [Page 8] Internet-Draft SSH Protocol Assigned Numbers October 2004 4.5.1 Conventions Protocol packets containing the SSH_MSG_CHANNEL_REQUEST message with a "pty-req" string MUST contain "encoded terminal modes" with an opcode of 1 byte. The opcode values are in the range of 1 to 255. Opcodes 1 to 159 have a single uint32 argument. Opcodes 160 to 255 are not yet defined. 4.5.2 Initial Assignments opcode argument description ------ -------- ----------- 0 TTY_OP_END Indicates end of options. 1 VINTR Interrupt character; 255 if none. Similarly for the other characters. Not all of these characters are supported on all systems. 2 VQUIT The quit character (sends SIGQUIT signal on POSIX systems). 3 VERASE Erase the character to left of the cursor. 4 VKILL Kill the current input line. 5 VEOF End-of-file character (sends EOF from the terminal). 6 VEOL End-of-line character in addition to carriage return and/or linefeed. 7 VEOL2 Additional end-of-line character. 8 VSTART Continues paused output (normally control-Q). 9 VSTOP Pauses output (normally control-S). 10 VSUSP Suspends the current program. 11 VDSUSP Another suspend character. 12 VREPRINT Reprints the current input line. 13 VWERASE Erases a word left of cursor. 14 VLNEXT Enter the next character typed literally, even if it is a special character 15 VFLUSH Character to flush output. 16 VSWTCH Switch to a different shell layer. 17 VSTATUS Prints system status line (load, command, pid, etc). 18 VDISCARD Toggles the flushing of terminal output. 30 IGNPAR The ignore parity flag. The parameter SHOULD be 0 if this flag is FALSE set, and 1 if it is TRUE. 31 PARMRK Mark parity and framing errors. 32 INPCK Enable checking of parity errors. 33 ISTRIP Strip 8th bit off characters. 34 INLCR Map NL into CR on input. 35 IGNCR Ignore CR on input. 36 ICRNL Map CR to NL on input. Lonvick Expires April 24, 2005 [Page 9] Internet-Draft SSH Protocol Assigned Numbers October 2004 37 IUCLC Translate uppercase characters to lowercase. 38 IXON Enable output flow control. 39 IXANY Any char will restart after stop. 40 IXOFF Enable input flow control. 41 IMAXBEL Ring bell on input queue full. 50 ISIG Enable signals INTR, QUIT, [D]SUSP. 51 ICANON Canonicalize input lines. 52 XCASE Enable input and output of uppercase characters by preceding their lowercase equivalents with "\". 53 ECHO Enable echoing. 54 ECHOE Visually erase chars. 55 ECHOK Kill character discards current line. 56 ECHONL Echo NL even if ECHO is off. 57 NOFLSH Don't flush after interrupt. 58 TOSTOP Stop background jobs from output. 59 IEXTEN Enable extensions. 60 ECHOCTL Echo control characters as ^(Char). 61 ECHOKE Visual erase for line kill. 62 PENDIN Retype pending input. 70 OPOST Enable output processing. 71 OLCUC Convert lowercase to uppercase. 72 ONLCR Map NL to CR-NL. 73 OCRNL Translate carriage return to newline (output). 74 ONOCR Translate newline to carriage return-newline (output). 75 ONLRET Newline performs a carriage return (output). 90 CS7 7 bit mode. 91 CS8 8 bit mode. 92 PARENB Parity enable. 93 PARODD Odd parity, else even. 128 TTY_OP_ISPEED Specifies the input baud rate in bits per second. 129 TTY_OP_OSPEED Specifies the output baud rate in bits per second. 4.5.3 Future Assignments Requests for assignments of new opcodes and their associated arguments MUST be done through the IETF CONSENSUS method as described in [RFC2434]. Lonvick Expires April 24, 2005 [Page 10] Internet-Draft SSH Protocol Assigned Numbers October 2004 4.6 Names In the following sections, the values for the name spaces are textual. The conventions and instructions to the IANA for future assignments are given in this section. The initial assignments are given in their respective sections. 4.6.1 Conventions for Names All names registered by the IANA in the following sections MUST be printable US-ASCII strings, and MUST NOT contain the characters at-sign ("@"), comma (","), or whitespace or control characters (ASCII codes 32 or less). Names are case-sensitive, and MUST NOT be longer than 64 characters. A provision is made here for locally extensible names. The IANA will not register, and will not control names with the at-sign ("@") in them. Names with the at-sign in them will have the format of "name@domainname" (without the double quotes) where the part preceeding the at-sign is the name. The format of the part preceding the at sign is not specified, however these names MUST be printable US-ASCII strings, and MUST NOT contain the comma character (","), or whitespace, or control characters (ASCII codes 32 or less). The part following the at-sign MUST be a valid, fully qualified internet domain name [RFC1034] controlled by the person or organization defining the name. Names are case-sensitive, and MUST NOT be longer than 64 characters. It is up to each domain how it manages its local namespace. It has been noted that these names resemble [RFC0822] email addresses. This is purely coincidental and actually has nothing to do with [RFC0822]. An example of a locally defined name is "ourcipher-cbc@example.com" (without the double quotes). 4.6.2 Future Assignments of Names Requests for assignments of new Names MUST be done through the IETF CONSENSUS method as described in [RFC2434]. 4.7 Service Names The Service Name is used to describe a protocol layer. Service name Reference ------------- --------- ssh-userauth [SSH-USERAUTH] ssh-connection [SSH-CONNECT] Lonvick Expires April 24, 2005 [Page 11] Internet-Draft SSH Protocol Assigned Numbers October 2004 4.8 Authentication Method Names The Authentication Method Name is used to describe an authentication method for the "ssh-userauth" service [SSH-USERAUTH]. Method name Reference ------------ --------- publickey [SSH-USERAUTH, Section 4] password [SSH-USERAUTH, Section 5] hostbased [SSH-USERAUTH, Section 6] none [SSH-USERAUTH, Section 2.3] 4.9 Connection Protocol Assigned Names The following are the Connection Protocol Type and Request names. 4.9.1 Connection Protocol Channel Types Channel type Reference ------------ --------- session [SSH-CONNECT, Section 4.1] x11 [SSH-CONNECT, Section 4.3.2] forwarded-tcpip [SSH-CONNECT, Section 5.2] direct-tcpip [SSH-CONNECT, Section 5.2] 4.9.2 Connection Protocol Global Request Names Request type Reference ------------ --------- tcpip-forward [SSH-CONNECT, Section 5.1] cancel-tcpip-forward [SSH-CONNECT, Section 5.1] 4.9.3 Connection Protocol Channel Request Names Request type Reference ------------ --------- pty-req [SSH-CONNECT, Section 4.2] x11-req [SSH-CONNECT, Section 4.3.1] env [SSH-CONNECT, Section 4.4] shell [SSH-CONNECT, Section 4.5] exec [SSH-CONNECT, Section 4.5] subsystem [SSH-CONNECT, Section 4.5] window-change [SSH-CONNECT, Section 4.7] xon-xoff [SSH-CONNECT, Section 4.8] signal [SSH-CONNECT, Section 4.9] Lonvick Expires April 24, 2005 [Page 12] Internet-Draft SSH Protocol Assigned Numbers October 2004 exit-status [SSH-CONNECT, Section 4.10] exit-signal [SSH-CONNECT, Section 4.10] 4.9.4 Initial Assignment of Signal Names Signal Reference ------ --------- ABRT [SSH-CONNECT] ALRM [SSH-CONNECT] FPE [SSH-CONNECT] HUP [SSH-CONNECT] ILL [SSH-CONNECT] INT [SSH-CONNECT] KILL [SSH-CONNECT] PIPE [SSH-CONNECT] QUIT [SSH-CONNECT] SEGV [SSH-CONNECT] TERM [SSH-CONNECT] USR1 [SSH-CONNECT] USR2 [SSH-CONNECT] 4.10 Key Exchange Method Names The Key Exchange Method Name describes a key-exchange method for the protocol [SSH-TRANS]. Note that, for historical reasons, the name "diffie-hellman-group1-sha1" is used for a key exchange method using Oakley Group 2. This is considered an aberration and should not be repeated. Any future specifications of Diffie Hellman key exchange using Oakley groups defined in [RFC2412] or its successors should be named using the group numbers assigned by IANA, and names of the form "diffie-hellman-groupN-sha1" should be reserved for this purpose. Editor's Note: diffie-hellman-group14-sha1 is controversial at the moment. It is being discussed on the mailing list. Method name Reference ------------ --------- diffie-hellman-group1-sha1 [SSH-TRANS, Section 8.1] diffie-hellman-group14-sha1 [SSH-TRANS, Section 8.2] 4.11 Assigned Algorithm Names The following names identify the Encryption Algorithm Names. Lonvick Expires April 24, 2005 [Page 13] Internet-Draft SSH Protocol Assigned Numbers October 2004 4.11.1 Encryption Algorithm Names Cipher name Reference ------------ --------- 3des-cbc [SSH-TRANS, Section 4.3] blowfish-cbc [SSH-TRANS, Section 4.3] twofish256-cbc [SSH-TRANS, Section 4.3] twofish-cbc [SSH-TRANS, Section 4.3] twofish192-cbc [SSH-TRANS, Section 4.3] twofish128-cbc [SSH-TRANS, Section 4.3] aes256-cbc [SSH-TRANS, Section 4.3] aes192-cbc [SSH-TRANS, Section 4.3] aes128-cbc [SSH-TRANS, Section 4.3] serpent256-cbc [SSH-TRANS, Section 4.3] serpent192-cbc [SSH-TRANS, Section 4.3] serpent128-cbc [SSH-TRANS, Section 4.3] arcfour [SSH-TRANS, Section 4.3] idea-cbc [SSH-TRANS, Section 4.3] cast128-cbc [SSH-TRANS, Section 4.3] none [SSH-TRANS, Section 4.3] des-cbc [FIPS-46-3] HISTORIC; See page 4 of [FIPS 46-3] 4.11.2 MAC Algorithm Names The following names identify the MAC Algorithm Names. MAC name Reference --------- --------- hmac-sha1 [SSH-TRANS, Section 4.4] hmac-sha1-96 [SSH-TRANS, Section 4.4] hmac-md5 [SSH-TRANS, Section 4.4] hmac-md5-96 [SSH-TRANS, Section 4.4] none [SSH-TRANS, Section 4.4] 4.11.3 Public Key Algorithm Names This table identifies the Public Key Algorithm names. Algorithm name Reference --------------- --------- ssh-dss [SSH-TRANS, Section 4.6] ssh-rsa [SSH-TRANS, Section 4.6] x509v3-sign-rsa [SSH-TRANS, Section 4.6] x509v3-sign-dss [SSH-TRANS, Section 4.6] Lonvick Expires April 24, 2005 [Page 14] Internet-Draft SSH Protocol Assigned Numbers October 2004 spki-sign-rsa [SSH-TRANS, Section 4.6] spki-sign-dss [SSH-TRANS, Section 4.6] pgp-sign-rsa [SSH-TRANS, Section 4.6] pgp-sign-dss [SSH-TRANS, Section 4.6] 4.11.4 Compression Algorithm Names The following names identify the Compression Algorithm names. Algorithm name Reference --------------- --------- none [SSH-TRANS, Section 4.2] zlib [SSH-TRANS, Section 4.2] 5. References 5.1 Normative References [SSH-ARCH] Ylonen, T. and C. Lonvick, "SSH Protocol Architecture", I-D draft-ietf-architecture-17.txt, October 2004. [SSH-TRANS] Ylonen, T. and C. Lonvick, "SSH Transport Layer Protocol", I-D draft-ietf-transport-19.txt, October 2004. [SSH-USERAUTH] Ylonen, T. and C. Lonvick, "SSH Authentication Protocol", I-D draft-ietf-userauth-22.txt, October 2004. [SSH-CONNECT] Ylonen, T. and C. Lonvick, "SSH Connection Protocol", I-D draft-ietf-connect-20.txt, October 2004. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2412] Orman, H., "The OAKLEY Key Determination Protocol", RFC 2412, November 1998. [RFC2434] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. Lonvick Expires April 24, 2005 [Page 15] Internet-Draft SSH Protocol Assigned Numbers October 2004 5.2 Informative References [RFC0822] Crocker, D., "Standard for the format of ARPA Internet text messages", STD 11, RFC 822, August 1982. [RFC1034] Mockapetris, P., "Domain names - concepts and facilities", STD 13, RFC 1034, November 1987. [FIPS-46-3] U.S. Dept. of Commerce, "FIPS PUB 46-3, Data Encryption Standard (DES)", October 1999. Author's Address Chris Lonvick (editor) Cisco Systems, Inc 12515 Research Blvd. Austin 78759 USA EMail: clonvick@cisco.com Lonvick Expires April 24, 2005 [Page 16] Internet-Draft SSH Protocol Assigned Numbers October 2004 Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. The IETF has been notified of intellectual property rights claimed in regard to some or all of the specification contained in this document. For more information consult the online list of claimed rights. Disclaimer of Validity This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. Lonvick Expires April 24, 2005 [Page 17] Internet-Draft SSH Protocol Assigned Numbers October 2004 Acknowledgment Funding for the RFC Editor function is currently provided by the Internet Society. Lonvick Expires April 24, 2005 [Page 18]