Internet Draft C. DeSanti V. Gaonkar K. McCloghrie S. Gai Cisco Systems 9 October 2004 Fibre Channel Fabric Address Manager MIB draft-ietf-imss-fc-fam-mib-00.txt Status of this Memo By submitting this Internet-Draft, I certify that any applicable patent or other IPR claims of which I am aware have been disclosed, and any of which I become aware will be disclosed, in accordance with RFC 3668. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress". The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright Notice Copyright (C) The Internet Society (2004). All Rights Reserved. Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for information related to a Fibre Channel network's Fabric Address Manager. At present, this memo is a work item of T11.5 (http://www.t11.org). The plan is that it will later be a work item of the IETF's IMSS working group. Expires April 2005 [Page 1] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 Table of Contents 1 Introduction ................................................. 3 2 The Internet-Standard Management Framework ................... 3 3 Short Overview of Fibre Channel .............................. 3 4 Relationship to Other MIBs ................................... 4 5 MIB Overview ................................................. 5 5.1 Fibre Channel management instance .......................... 5 5.2 Switch Index ............................................... 5 5.3 Fabric Index ............................................... 5 5.4 The t11FamGroup group ...................................... 6 5.5 The t11FamDatabaseGroup group .............................. 6 5.6 The t11FamAreaGroup group .................................. 6 5.7 The t11FamCacheGroup group ................................. 6 5.8 The t11FamCommandGroup group ............................... 6 5.9 The t11FamNotificationGroup group .......................... 7 5.10 Use of RCF and BF ......................................... 7 6 Definitions .................................................. 8 6.1 T11-TC-MIB ................................................. 8 6.2 T11-FC-FABRIC-ADDR-MGR-MIB ................................. 9 7 Intellectual Property ........................................ 34 8 Acknowledgements ............................................. 34 9 Normative References ......................................... 34 10 Informative References ...................................... 35 11 Security Considerations ..................................... 36 12 Authors' Addresses .......................................... 37 13 Full Copyright Statement .................................... 38 Expires April 2005 [Page 2] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 1. Introduction This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects for information related to a Fibre Channel network's Fabric Address Manager. Fabric Address Manager refers to the functionality of acquiring DomainID(s) as specified in [FC-SW-3], and managing Fibre Channel Identifiers as specified in [FC-FS]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 3. Short Overview of Fibre Channel The Fibre Channel (FC) is logically a bidirectional point-to-point serial data channel, structured for high performance. Fibre Channel provides a general transport vehicle for higher level protocols such as Small Computer System Interface (SCSI) command sets, the High- Performance Parallel Interface (HIPPI) data framing, IP (Internet Protocol), IEEE 802.2, and others. Physically, Fibre Channel is an interconnection of multiple communication points, called N_Ports, interconnected either by a switching network, called a Fabric, or by a point-to-point link. A Fibre Channel "node" consists of one or more N_Ports. A Fabric may consist of multiple Interconnect Elements, some of which are switches. An N_Port connects to the Fabric via a port on a switch called an F_Port. When multiple FC nodes are connected to a single port on a switch via an "Arbitrated Loop" topology, the switch port is called an FL_Port, and the nodes' ports are called NL_Ports. The Expires April 2005 [Page 3] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 term Nx_Port is used to refer to either an N_Port or an NL_Port. The term Fx_Port is used to refer to either an F_Port or an FL_Port. A switch port, which is interconnected to another switch port via an Inter Element Link (IEL), is called an E_Port. A B_Port connects a bridge device with an E_Port on a switch; a B_Port provides a subset of E_Port functionality. Many Fibre Channel components, including the fabric, each node, and most ports, have globally-unique names. These globally-unique names are typically formatted as World Wide Names (WWNs). More information on WWNs can be found in [FC-FS]. WWNs are expected to be persistent across agent and unit resets. Fibre Channel frames contain 24-bit address identifiers which identify the frame's source and destination ports. Each FC port has both an address identifier and a WWN. When a fabric is in use, the FC address identifiers are dynamically assigned by a switch. Each octet of a 24-bit address represents a level in an address hierarchy, with a Domain_ID being the highest level of the hierarchy. Each Switch in a Fabric is assigned one (or more) unique Domain_IDs using a two-step process. First, one switch, called Principal Switch, is selected from the switches of a Fabric. Then, the Principal Switch assigns Domain_IDs to the other switches of the Fabric. Address assignment within a Domain is performed by the switch to which that Domain_ID is granted. 4. Relationship to Other MIBs The first standardized MIB for Fibre Channel [RFC2837] was focused on Fibre Channel switches. It is being replaced by the more generic Fibre Channel Management MIB [FC-MGMT] which defines basic information for Fibre Channel hosts and switches, including extensions to the standard IF-MIB [RFC2863] for Fibre Channel interfaces. [FC-MGMT] includes the specification of how the generic objects defined in [IF-MIB] apply to Fibre Channel interfaces. Note that an interface's ifIndex value must be unique within an SNMP context, irrespective of how many Fibre Channel management instances (see below) and how many Fibre Channel switches are instrumented within that SNMP context. This document defines the T11-FC-FABRIC-ADDR-MGR-MIB module which extends beyond [FC-MGMT] to cover the functionality, in Fibre Channel Expires April 2005 [Page 4] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 switches, which is used to manage fabric configuration, domains, and addresses within a domain. This document also contains a MIB module, T11-TC-MIB, to define Textual Conventions which might also be useful in other MIBs defined by T11. 5. MIB Overview This section explains the use of a Fibre Channel management instance, a Switch Index, and a Fabric Index. It also describes the six MIB groups contained in the MIB. 5.1. Fibre Channel management instance A Fibre Channel management instance is defined in [FC-MGMT] as a separable managed instance of Fibre Channel functionality. Fibre Channel functionality may be grouped into Fibre Channel management instances in whatever way is most convenient for the implementation(s). For example, one such grouping accommodates a single SNMP agent having multiple AgentX [RFC2741] sub-agents, with each sub-agent implementing a different Fibre Channel management instance. The object, fcmInstanceIndex, is IMPORTed from the FC-MGMT-MIB [FC-MGMT] as the index value to uniquely identify a Fibre Channel management instance. 5.2. Switch Index The FC-MGMT-MIB [FC-MGMT] defines the fcmSwitchTable as a table of information about Fibre Channel switches which are managed by Fibre Channel management instances. Each Fibre Channel management instance can manage one or more Fibre Channel switches. The Switch Index, fcmSwitchIndex, is IMPORTed from the FC-MGMT-MIB as the index value to uniquely identify a Fibre Channel switch amongst those (one or more) managed by the same Fibre Channel management instance. 5.3. Fabric Index The current standard for an interconnecting Fabric consisting of multiple Fabric Switch elements is [FC-SW-3], which describes the operation of a single Fabric in a physical infrastructure. It is possible that future standards will define how multiple Fabrics could Expires April 2005 [Page 5] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 operate within one (or more) physical infrastructures. In such a scenario, each Fabric would, of course, have its own management instrumentation. Therefore, to *allow* for this future possibility, this MIB defines all Fabric-related information in tables which are INDEX-ed by an arbitrary integer, named a "Fabric Index", . In a Fabric which is conformant to [FC-SW-3], the value of this Fabric Index will always be 1. It is quite possible, and may even become likely, that (a port of) a Fibre Channel switch will be connected to multiple such Fabrics. Thus, in order to simplify a query concerning all the Fabrics to which a single switch is connected, fcmSwitchIndex will be listed before t11FamFabricIndex when they both appear in the same INDEX clause. 5.4. The t11FamGroup group This group contains basic information about the Fabric Address Manager functionality within a switch, including its configuration parameters which are per-interface (i.e., specified for a particular Fibre Channel interface identified by an ifIndex value). 5.5. The t11FamDatabaseGroup group This group contains information about which switches are assigned to which domains. 5.6. The t11FamAreaGroup group This group contains information about which Port-IDs have been assigned within the Areas of the local Domain. 5.7. The t11FamCacheGroup group This conditional mandatory group contains information about all the FC address identifier assignments which have been recently released. This cache is kept to support the concept of Preferred Domain_ID via a best effort attempt for (short-term) re-assignment of the same FC address identifiers. 5.8. The t11FamCommandGroup group This optional group contains objects used for initiating an operation on a Fabric. Expires April 2005 [Page 6] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 5.9. The t11FamNotificationGroup group This group contains notifications of significant events concerning the Fabric Address management functionality within a switch. 5.10. Use of RCF and BF Included in [FC-SW-3] is the specification of Reconfigure Fabric (RCF) and Build Fabric (BF), both of which are command-codes of the Switch Fabric Internal Link Service (SW_ILS). [FC-SW-3] includes the warning: NOTE 13 - Since the RCF causes a complete reconfiguration of the Fabric, and may cause addresses allocated to a Switch to change, this SW_ILS should be used with caution. The BF SW_ILS allows the Fabric to attempt reconfiguration without loss of or change of address and therefore should be attempted before an RCF. Examples of situations in which RCF may be appropriate include resolution of overlapped Domains, or the failure of a Fabric Reconfiguration initiated by a BF. Further, [FC-MI] specifies A Fabric is prohibited from autonomously generating a RCF, but an outside administrative function may request a switch to generate an RCF. Such an administrative function is outside the scope of this technical report. The T11-FC-FABRIC-ADDR-MGR-MIB defined in this document is consistent with both of the above quotes since it defines two objects, t11FamAutoReconfigure and t11FamRestart, which are defined with a MAX-ACCESS of read-write, and setting them to the appropriate value is a means by which "an outside administrative function may request a switch to generate an RCF" [FC-MI]. Note, however, the MIB specifies in its compliance section that the minimum required level of support for these two objects is read-only. Further, for both t11FamAutoReconfigure and t11FamRestart, the MIB serves only as a request to generate; it does not represent the action of the RCF or BF. That is, a successful SNMP SetRequest on these objects will cause an RCF (or BF) to be sent, but SNMP does not/can not ensure the successful operation of the SW_ILS operation. Expires April 2005 [Page 7] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 6. Definitions 6.1. T11-TC-MIB T11-TC-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, Unsigned32 FROM SNMPv2-SMI -- [RFC2578] TEXTUAL-CONVENTION FROM SNMPv2-TC; -- [RFC2579] t11TcMIB MODULE-IDENTITY LAST-UPDATED "200406050000Z" ORGANIZATION "T11" CONTACT-INFO " Claudio DeSanti Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 408 853-9172 EMail: cds@cisco.com Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA 95134 Phone: +1 408-526-5260 Email: kzm@cisco.com" DESCRIPTION "This module defines textual conventions used in T11 MIBs." REVISION "200406050000Z" DESCRIPTION "Initial version of this MIB module." ::= { tbd } FabricIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A Fabric Index which is used as a unique index value to identify a particular Fabric within one (or more) physical infrastructures. In an environment which is conformant to FC-SW-3, where there is always exactly one Fabric in a single physical infrastructure, the value of this Fabric Index will always be 1. Expires April 2005 [Page 8] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 In environments conformant to other specifications, the value of this Fabric Index can have other values." SYNTAX Unsigned32 END 6.2. T11-FC-FABRIC-ADDR-MGR-MIB T11-FC-FABRIC-ADDR-MGR-MIB DEFINITIONS ::= BEGIN -- the Fibre Channel Fabric Address Manager MIB -- -- for management of the functionality, in Fibre Channel switches, -- which is used to manage fabric configuration, domains, and -- addresses within a domain. -- IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32, Counter32, Gauge32 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] TEXTUAL-CONVENTION, TruthValue, RowStatus FROM SNMPv2-TC -- [RFC2579] ifIndex FROM IF-MIB -- [IF-MIB] fcmInstanceIndex, fcmSwitchIndex, FcDomainIdOrZero, FcNameIdOrZero FROM FC-MGMT-MIB -- [FC-MGMT] FabricIndex FROM T11-TC-MIB; t11FabricAddrMgrMIB MODULE-IDENTITY LAST-UPDATED "200407170000Z" ORGANIZATION "T11" CONTACT-INFO " Claudio DeSanti Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 408 853-9172 EMail: cds@cisco.com Keith McCloghrie Cisco Systems, Inc. Expires April 2005 [Page 9] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 170 West Tasman Drive San Jose, CA USA 95134 Phone: +1 408-526-5260 Email: kzm@cisco.com" DESCRIPTION "The MIB module for the Fabric Address management functionality defined by the Fibre Channel standards. For the purposes of this MIB, Fabric Address Manager refers to the functionality of acquiring DomainID(s) as specified in FC-SW-3, and managing Fibre Channel Identifiers as specified in FC-FS. An instance of 'Fabric Address Manager' software functionality executes in the principal switch, and in each other switch." REVISION "200407170000Z" DESCRIPTION "Initial version of this MIB module." ::= { tbd } t11FamMIBObjects OBJECT IDENTIFIER ::= { t11FabricAddrMgrMIB 1 } t11FamMIBConformance OBJECT IDENTIFIER ::= { t11FabricAddrMgrMIB 2 } t11FamConfiguration OBJECT IDENTIFIER ::= { t11FamMIBObjects 1 } t11FamInfo OBJECT IDENTIFIER ::= { t11FamMIBObjects 2 } t11FamNotifyControl OBJECT IDENTIFIER ::= { t11FamMIBObjects 3 } t11FamNotifications OBJECT IDENTIFIER ::= { t11FamMIBObjects 0 } -- Textual Conventions T11FamDomainPriority ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Priority of a switch. The principal switch selection is influenced by the priority of the switches. Some values are of importance are: 1 : The highest priority in principal switch selection, which is used by the administrator to establish which switch becomes the principal switch. 255 : Indicates that the switch is not capable of acting as a principal switch." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, section 6.1.5." SYNTAX Unsigned32 (1..255) T11FamDomainInterfaceRole ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION Expires April 2005 [Page 10] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 "The 'designated' state/role of the ISL to which an interface connects, or (if not connected) the state of the interface: nonPrincipal (1) - non-Principal ISL principalUpstream (2) - Upstream Principal ISL principalDownsteam (3) - Downstream Principal ISL isolated (4) - interface is isolated down (5) - interface is down unknown (6) - state/role is unknown " REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, June 2004, Sections 3.1, 5.7, and Figure 9." SYNTAX INTEGER { nonPrincipal (1), principalUpstream (2), principalDownsteam (3), isolated (4), down (5), unknown (6) } T11FamState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The state of the Fabric Address Manager, as described in FC-SW-3's Table 86 and Figure 15. - 'starting' represents a switch engaged in the process represented by the first row in Table 86, - 'principalSwitchSelection' represents a switch engaged in the process represented by the second row in Table 86, but not in states F0 or F1 of Figure 15. - 'domainIdDistribution' represents a switch engaged in the process represented by the third row in Table 86, - 'stable' represents a switch which has successfully completed the process represented by the third row in Table 86 and has at least one E_Port - 'stableWithNoEports' represents a switch which has successfully completed the process represented by the third row in Table 86 but has no E_Ports Expires April 2005 [Page 11] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 - 'noDomains' represents a switch which has completed the process represented by the third row in Table 86 but failed to obtain a Domain_ID - 'unconfigured' represents a switch which requires operator input before it can begin the process represented by the first row in Table 86, - 'buildFabricPhase' represents a switch which is in state F0 of Figure 15. - 'reconfigureFabricPhase' represents a switch which is in state F1 of Figure 15. - 'unknown' represents a switch which is confused about what state it is in. - 'other' represents a switch which is in a state not represented by any of the above enumerations." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, Table 86 and Figure 15." SYNTAX INTEGER { other(1), starting(2), unconfigured(3), principalSwitchSelection(4), domainIdDistribution(5), buildFabricPhase(6), reconfigureFabricPhase(7), stable(8), stableWithNoEports(9), noDomains(10), unknown(11) } -- -- t11FamTable -- t11FamTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires April 2005 [Page 12] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 "This table contains Fabric Address Manager related parameters which are able to be configured and monitored in a Fibre Channel switch. For each of the switches (identified by fcmSwitchIndex) managed by a Fibre Channel management instance (identified by fcmInstanceIndex), there is an entry for each Fabric known to such a switch. Entries are implicitly created/removed if and when additional Fabrics are created/deleted." ::= { t11FamConfiguration 1 } t11FamEntry OBJECT-TYPE SYNTAX T11FamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry provides information on the local Fabric Address Manager functionality for a Fabric known to a particular switch." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FamFabricIndex } ::= { t11FamTable 1 } T11FamEntry ::= SEQUENCE { t11FamFabricIndex FabricIndex, t11FamConfigDomainId FcDomainIdOrZero, t11FamConfigDomainIdType INTEGER, t11FamAutoReconfigure TruthValue, t11FamContiguousAllocation TruthValue, t11FamPriority T11FamDomainPriority, t11FamPrincipalSwitchWwn FcNameIdOrZero, t11FamLocalSwitchWwn FcNameIdOrZero, t11FamAssignedAreaIdList OCTET STRING, t11FamGrantedFcIds Counter32, t11FamRecoveredFcIds Counter32, t11FamFreeFcIds Gauge32, t11FamAssignedFcIds Gauge32, t11FamAvailableFcIds Gauge32, t11FamRunningPriority T11FamDomainPriority, t11FamPrincSwRunningPriority T11FamDomainPriority, t11FamState T11FamState, t11FamPrincipalSwitchSelections Counter32, t11FamBuildFabrics Counter32, t11FamFabricReconfigures Counter32, t11FamDomainId FcDomainIdOrZero, t11FamLocalPrincipalSwitchSlctns Counter32, t11FamSticky TruthValue, Expires April 2005 [Page 13] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamRestart INTEGER, t11FamRcFabricNotifyEnable TruthValue } t11FamFabricIndex OBJECT-TYPE SYNTAX FabricIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique index value which uniquely identifies a particular Fabric known to a particular switch. In a Fabric conformant to SW-3, only a single Fabric can operate within a physical infrastructure, and thus, the value of this Fabric Index will always be 1. However, it is possible that future standards will define how multiple Fabrics, each with its own management instrumentation, could operate within one (or more) physical infrastructures. To allow for this future possibility, this index value is used to uniquely identify a particular Fabric within a physical infrastructure." ::= { t11FamEntry 1 } t11FamConfigDomainId OBJECT-TYPE SYNTAX FcDomainIdOrZero MAX-ACCESS read-write STATUS current DESCRIPTION "The configured Domain_ID of the particular switch on this Fabric, or zero if no Domain_ID has been configured. The meaning of this object depends on t11FamConfigDomainIdType object. If t11FamConfigDomainIdType is 'preferred', then Domain_ID configured is called 'preferred Domain_ID'. The valid values are between 0 and 239. In a situation where this domain could not be assigned, any other Domain_ID would be acceptable. The value '0' means any Domain_ID. If t11FamConfigDomainIdType is 'static', then Domain_ID is called 'static Domain_ID' and valid values are between 1 and 239. In a situation where this domain was non-zero but could not be assigned, no other Domain_ID would be acceptable. Expires April 2005 [Page 14] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 The switch sends an RDI (Request Domain_ID) to request this Domain_ID. If a Domain_ID is not able to be granted in the case of 'preferred', or if a 'static' Domain_ID is configured but not able to be granted, then it is an error condition. When this error occurs, the switch will continue as if it receives a SW_RJT with a reason/explanation of: 'Unable to perform command request'/'Domain_ID not available'. That is, its E_Ports on that Fabric will be isolated and the administrator informed via a 't11FamDomainIdNotAssigned' notification." DEFVAL { 0 } ::= { t11FamEntry 2 } t11FamConfigDomainIdType OBJECT-TYPE SYNTAX INTEGER { static (1), preferred(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Type of configured Domain_ID." DEFVAL { preferred } ::= { t11FamEntry 3 } t11FamAutoReconfigure OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object determines how a particular switch responds to certain error conditions. The condition that might cause these errors is the merging of two disjoint fabrics that have overlapping Domain_ID list. If value of this object is 'true', the switch will send a RCF (ReConfigureFabric) to rebuild the Fabric. If 'false' the switch will isolate the E_Ports on which the errors happened." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), December 2003, sections 6.1.12 & 7.3. Expires April 2005 [Page 15] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 Fibre Channel - Methodologies for Interconnects (FC-MI), December 2001, table 14, note g." DEFVAL { false } ::= { t11FamEntry 4 } t11FamContiguousAllocation OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Determines how a particular switch behaves when elected as the principal switch. If true, the switch will only accept RDIs with a contiguous allocation; specifically, it will reject RDIs with non-contiguous Domain_IDs, and if an RDI for a contiguous Domain_ID is not able to be fulfilled, it will try to replace all the Domain_IDs in the list with contiguous Domain_IDs, and if that fails, the RDI will be rejected. If false, then the switch acts normally in granting the Domain_IDs even if they are not contiguous." ::= { t11FamEntry 5 } t11FamPriority OBJECT-TYPE SYNTAX T11FamDomainPriority MAX-ACCESS read-write STATUS current DESCRIPTION "The initial or configured priority of a particular switch to be used in principal switch selection process." ::= { t11FamEntry 6 } t11FamPrincipalSwitchWwn OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The WWN of the Principal Switch on this Fabric, or zero-length string if the identity of the principal switch is unknown." DEFVAL { ''H } ::= { t11FamEntry 7 } t11FamLocalSwitchWwn OBJECT-TYPE Expires April 2005 [Page 16] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 SYNTAX FcNameIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The WWN of the particular Switch on this Fabric." ::= { t11FamEntry 8 } t11FamAssignedAreaIdList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The list of (zero or more) Area_IDs which have been assigned by a particular switch in this Fabric, formatted as an array of octets in ascending order. Each octet represents one Area_ID. So, the list containing Area_IDs: 23, 45, 235 and 56 would be formatted as the 4-octet string x'172d38eb'. A particular Area's Area_ID is used as the index into the t11FamAreaTable to get the statistics on that Area." ::= { t11FamEntry 9 } t11FamGrantedFcIds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Fibre Channel Address Identifiers granted (for local use, i.e., with a particular switch's Domain_ID) by the Fabric Address Manager on that switch." ::= { t11FamEntry 10 } t11FamRecoveredFcIds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Fibre Channel Address Identifiers that have been recovered by the Fabric Address Manager on a particular switch since the switch has been initialized. A recovered Fibre Channel Address Identifier is one that is explicitly returned after previously being used." ::= { t11FamEntry 11 } Expires April 2005 [Page 17] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamFreeFcIds OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Fibre Channel Address Identifiers that are currently unassigned on this Fabric and could be available for assignment either immediately or at some later time. The sum of the instances of FreeFcIds and AssignedFcIds corresponding to a particular Fabric is the total number of Fibre Channel Address Identifiers that the local Fabric Address Management is capable of assigning on that Fabric." ::= { t11FamEntry 12 } t11FamAssignedFcIds OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Fibre Channel Address Identifiers that are currently assigned on this Fabric. The sum of the instances of FreeFcIds and AssignedFcIds corresponding to a particular Fabric is the total number of Fibre Channel Address Identifiers that the local Fabric Address Management is capable of assigning on that Fabric." ::= { t11FamEntry 13 } t11FamAvailableFcIds OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Fibre Channel Address Identifiers that are unassigned and currently available for immediate assignment on the Fabric, e.g., with the 'Clean Address' bit set to 1." REFERENCE "Fibre Channel - Framing and Signaling (FC-FS), ANSI INCITS 373-2003, section 15.6.2.4.2, April 2003." ::= { t11FamEntry 14 } t11FamRunningPriority OBJECT-TYPE SYNTAX T11FamDomainPriority MAX-ACCESS read-only Expires April 2005 [Page 18] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 STATUS current DESCRIPTION "The running priority of a particular switch on this Fabric. This value is initialised to the value of t11FamPriority, and subsequently altered as specified by the procedures defined in FC-SW-3." ::= { t11FamEntry 15 } t11FamPrincSwRunningPriority OBJECT-TYPE SYNTAX T11FamDomainPriority MAX-ACCESS read-only STATUS current DESCRIPTION "The running priority of the principal switch on this Fabric." ::= { t11FamEntry 16 } t11FamState OBJECT-TYPE SYNTAX T11FamState MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Fabric Address Manager on a particular switch on this Fabric." ::= { t11FamEntry 17 } t11FamLocalPrincipalSwitchSlctns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a particular switch became the principal switch on this Fabric." ::= { t11FamEntry 18 } t11FamPrincipalSwitchSelections OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of principal switch selections on this Fabric." ::= { t11FamEntry 19 } t11FamBuildFabrics OBJECT-TYPE SYNTAX Counter32 Expires April 2005 [Page 19] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of non-disruptive fabric reconfigurations (BFs) that have occurred on this Fabric." ::= { t11FamEntry 20 } t11FamFabricReconfigures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of disruptive fabric reconfigurations (RCFs) that have occurred on this Fabric." ::= { t11FamEntry 21 } t11FamDomainId OBJECT-TYPE SYNTAX FcDomainIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The Domain_ID of a particular switch on this Fabric or zero if no Domain_ID has been assigned." ::= { t11FamEntry 22 } t11FamSticky OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of whether a particular switch is supporting the concept of Preferred Domain_IDs via a best effort attempt to re-assign the same Fibre Channel Address Identifier value to a port on the next occasion when a port requests an assignment on this Fabric. If the value of this object is 'true', then the switch is maintaining rows in the t11FamFcIdCacheTable for this Fabric." ::= { t11FamEntry 23 } t11FamRestart OBJECT-TYPE SYNTAX INTEGER { nonDisruptive(1), disruptive(2), Expires April 2005 [Page 20] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 noOp(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object tells the Fabric Address Manager to request a fabric reconfiguration. If this object is set to 'disruptive', then a RCF (ReConfigure Fabric) is generated in the Fabric in order for the fabric to recover from the errors. If this object is set to 'nonDisruptive', then a BF (Build Fabric) is generated in the Fabric. No action is taken if this object is set to 'noOp'. The value of the object when read is always 'noOp'." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, June 2004, section 7.3." ::= { t11FamEntry 24 } t11FamRcFabricNotifyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether or not a particular switch should issue a t11FamFabricChangeNotify notification on sending or receiving ReConfigureFabric (RCF) on a Fabric. If the value of the object is 'true, then the notification is generated. If the value is 'false', notification is not generated. If an implementation requires all fabrics to have the same value, then setting one instance of this object to a new object will result in all corresponding instances being set to that same new value." DEFVAL { false } ::= { t11FamEntry 25 } -- -- t11FamIfTable - Interface configuration -- Expires April 2005 [Page 21] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamIfTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FamIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains those Fabric Address Manager parameters and status values, which are per-interface (identified by an ifIndex value), per-Fabric (identified by a t11FamFabricIndex value), and per-switch (identified by values of fcmInstanceIndex and fcmSwitchIndex). An entry in this table is automatically created when an E_Port becomes non-isolated on a particular Fabric. An entry is deleted automatically from this table if: a) the corresponding interface is no longer an E_Port (e.g., a G_Port which is dynamically determined to be an F_Port), and all configuration parameter(s) have default values; or b) the interface identified by ifIndex no longer exists (e.g., because a line-card is physically removed); or c) the row in the t11FamTable corresponding the fabric identified by t11FamFabricID no longer exists. Creating an entry in this table via t11FamIfRowStatus provides the means to specify non-default parameter value(s) for an interface at a time when the relevant row in this table does not exist, i.e., because the interface is either down or it is not an E_Port." ::= { t11FamConfiguration 2 } t11FamIfEntry OBJECT-TYPE SYNTAX T11FamIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information on the interface configuration on the Fabric identified by t11FamFabricIndex." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FamFabricIndex, ifIndex} ::= { t11FamIfTable 1 } T11FamIfEntry ::= SEQUENCE { t11FamIfRcfReject TruthValue, t11FamIfRole T11FamDomainInterfaceRole, Expires April 2005 [Page 22] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamIfRowStatus RowStatus } t11FamIfRcfReject OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object determines if the incoming ReConfigure Fabric (RCF) messages on this interface on this Fabric is accepted or not. If this object is 'true', then the incoming RCF is rejected. If 'false', incoming RCF is accepted. Note that this object does not apply to the outgoing RCFs generated by this interface." DEFVAL {false} ::= { t11FamIfEntry 1 } t11FamIfRole OBJECT-TYPE SYNTAX T11FamDomainInterfaceRole MAX-ACCESS read-only STATUS current DESCRIPTION "The role of this interface." ::= { t11FamIfEntry 2 } t11FamIfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row." ::= { t11FamIfEntry 3 } -- -- t11FamAreaTable -- t11FamAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FamAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires April 2005 [Page 23] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 "This table contains Area assignments per-Fabric by a switch's Fabric Address Manager. Each octet in t11FamAssignedAreaList is able to be used to index into this table to find information on each Area." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, June 2004, section 4.8." ::= { t11FamInfo 1 } t11FamAreaEntry OBJECT-TYPE SYNTAX T11FamAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry gives information on the Area_ID and all Port_IDs that have been assigned within an Area for the Fabric identified by t11FamFabricIndex, by the Fabric Address Manager in the switch identified by fcmInstanceIndex and fcmSwitchIndex." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FamFabricIndex, t11FamAreaAreaId} ::= { t11FamAreaTable 1 } T11FamAreaEntry ::= SEQUENCE { t11FamAreaAreaId Unsigned32, t11FamAreaAssignedPortIdList OCTET STRING } t11FamAreaAreaId OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Area_ID of this Area." ::= { t11FamAreaEntry 1 } t11FamAreaAssignedPortIdList OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The list of Port_IDs which have been assigned in this Area and Fabric, formatted as an array of octets in ascending order. There could be zero or more Port_IDs assigned on this Area and Fabric. Expires April 2005 [Page 24] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 Each octet represents one Port_ID. So, the list containing the Port_IDs 23, 45, 235 and 56 would be formatted as the 4-octet string x'172d38eb'." ::= { t11FamAreaEntry 2 } -- -- t11FamDatabaseTable -- t11FamDatabaseTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FamDatabaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all information known by the a switch about all the domains which have been assigned in each Fabric." REFERENCE "Fibre Channel - Switch Fabric - 3 (FC-SW-3), ANSI INCITS 384-2004, June 2004, section 4.8." ::= { t11FamInfo 2 } t11FamDatabaseEntry OBJECT-TYPE SYNTAX T11FamDatabaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the t11FamDatabaseTable containing information about one Domain_ID in the Fabric identified by t11FamFabricIndex, and known by the switch identified by t11FamFabricIndex and t11FamDatabaseDomainId." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FamFabricIndex , t11FamDatabaseDomainId} ::= { t11FamDatabaseTable 1 } T11FamDatabaseEntry ::= SEQUENCE { t11FamDatabaseDomainId FcDomainIdOrZero, t11FamDatabaseSwitchWwn FcNameIdOrZero } t11FamDatabaseDomainId OBJECT-TYPE SYNTAX FcDomainIdOrZero (1..239) MAX-ACCESS not-accessible STATUS current Expires April 2005 [Page 25] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 DESCRIPTION "The Domain_ID for which this row contains information. The value must be non-zero." ::= { t11FamDatabaseEntry 1 } t11FamDatabaseSwitchWwn OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The Node name (WWN) of the switch to which the corresponding value of t11FamDatabaseDomainId is currently assigned for the particular Fabric." ::= { t11FamDatabaseEntry 2 } -- -- Fibre Channel Address Identifier cache information -- -- The cached information allows the Fabric Address Manager to -- implement the concept of a Preferred Domain_ID, whereby after a port -- releases a Fibre Channel Address Identifier value, a switch makes an -- attempt to re-assign the same Fibre Channel Address Identifier value -- on the next occasion when that port requests an assignment. -- t11FamMaxFcIdCacheSize OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of Fibre Channel Address Identifiers that are able to be cached in the t11FamFcIdCacheTable. If the number is unknown, the value of this object is zero." ::= { t11FamInfo 3 } -- -- t11FamFcIdCacheTable -- t11FamFcIdCacheTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FamFcIdCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Expires April 2005 [Page 26] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 "This table contains all the Fibre Channel Address Identifiers that have recently been released by the Fabric Address Manager in a switch . So, it lists all the Fibre Channel Address Identifiers that have valid WWN-to-Fibre Channel Address Identifier mappings and are currently not assigned to any ports. These Fibre Channel Address Identifier were assigned to ports but have since been released. These cached Fibre Channel Address Identifiers contain only Area_ID and Port_ID information. This cache is kept to provide best effort re-assignment of same Fibre Channel Address Identifiers, i.e., when an Nx_Port asks for an Fibre Channel Address Identifier, soon after releasing one, the same value is re-assigned, if possible." ::= { t11FamInfo 4 } t11FamFcIdCacheEntry OBJECT-TYPE SYNTAX T11FamFcIdCacheEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the t11FamFcIdCacheTable containing information about one Fibre Channel Address Identifier that was released from a WWN, corresponding to a range of one or more ports connected to the switch (identified by t11FamFabricIndex and t11FamFcIdCacheWwn) in the Fabric (identified by t11FamFabricIndex). An entry is created when a Fibre Channel Address Identifier is released by the last port in the range. The oldest entry is deleted if the number of rows in this table reaches t11FamMaxFcIdCacheSize, and its space is required for a new entry. An entry is also deleted when its Fibre Channel Address Identifier is assigned to a port." INDEX { fcmInstanceIndex, fcmSwitchIndex, t11FamFabricIndex, t11FamFcIdCacheWwn} ::= { t11FamFcIdCacheTable 1 } T11FamFcIdCacheEntry ::= SEQUENCE { t11FamFcIdCacheWwn FcNameIdOrZero, t11FamFcIdCacheAreaIdPortId OCTET STRING, t11FamFcIdCachePortIds Unsigned32 } t11FamFcIdCacheWwn OBJECT-TYPE SYNTAX FcNameIdOrZero Expires April 2005 [Page 27] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The N_Port_Name (WWN) of the port associated this entry." ::= { t11FamFcIdCacheEntry 1 } t11FamFcIdCacheAreaIdPortId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Area_ID and Port_ID of the first Fibre Channel Address Identifier in a range, that was assigned and has since been released on this Fabric. Note that this object is only 2 bytes and only contains the Area_ID and Port_ID." ::= { t11FamFcIdCacheEntry 2 } t11FamFcIdCachePortIds OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Port_IDs in the range all of which were assigned and later released. The range starts with the Port_ID contained in the second byte of t11FamFcIdCacheAreaIdPortId for the Area_ID contained in the first byte of object t11FamFcIdCacheAreaIdPortId." ::= { t11FamFcIdCacheEntry 3 } -- Objects for use in notifications t11FamNotifyFabricIndex OBJECT-TYPE SYNTAX FabricIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "A unique index value which identifies a particular Fabric for which a particular notification is generated. In a Fabric conformant to SW-3, only a single Fabric can operate within a physical infrastructure, and thus, the value of this Fabric Index will always be 1. Expires April 2005 [Page 28] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 However, it is possible that future standards will define how multiple Fabrics, each with its own management instrumentation, could operate within a single physical infrastructure. To allow for this future possibility, this value uniquely identifies the Fabric within the physical infrastructure for which a notification is generated." ::= { t11FamNotifyControl 2 } -- Notifications t11FamDomainIdNotAssignedNotify NOTIFICATION-TYPE OBJECTS { t11FamLocalSwitchWwn, t11FamNotifyFabricIndex } STATUS current DESCRIPTION "This notification indicates that a Domain_ID has not been not configured nor assigned for a particular Fabric, identified by t11FamNotifyFabricIndex, on a particular switch identified by t11FamLocalSwitchWwn. This could happen under the following conditions, and results in the switch isolating E_Ports on the Fabric: - if the switch's request for a configured static Domain_ID is rejected or no other Domain_ID is assigned, then the E_Ports are isolated." ::= { t11FamNotifications 1 } t11FamNewPrincipalSwitchNotify NOTIFICATION-TYPE OBJECTS { t11FamLocalSwitchWwn, t11FamNotifyFabricIndex } STATUS current DESCRIPTION "This notification indicates that a particular switch, identified by t11FamLocalSwitchWwn, has become the new Principal Switch on the Fabric identified by t11FamNotifyFabricIndex. This notification is sent soon after its election as the new Principal Switch, i.e., upon expiration of a Principal Switch selection timer which is equal to twice the Fabric Stability Timeout value (F_S_TOV)." ::= { t11FamNotifications 2 } t11FamFabricChangeNotify NOTIFICATION-TYPE OBJECTS { t11FamLocalSwitchWwn, t11FamNotifyFabricIndex } STATUS current DESCRIPTION Expires April 2005 [Page 29] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 "This notification is sent whenever a particular switch, identified by t11FamLocalSwitchWwn, sends or receives a Build Fabric (BF) or a ReConfigure Fabric (RCF) message on the Fabric identified by t11FamNotifyFabricIndex. This notification is not sent if a 't11FamNewPrincipalSwitchNotify' notification is sent for the same event." ::= { t11FamNotifications 3 } -- -- Conformance -- t11FamMIBCompliances OBJECT IDENTIFIER ::= { t11FamMIBConformance 1 } t11FamMIBGroups OBJECT IDENTIFIER ::= { t11FamMIBConformance 2 } t11FamMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for Fibre Channel switches which implement Fabric Address Manager functionality." MODULE MANDATORY-GROUPS { t11FamGroup, t11FamDatabaseGroup, t11FamAreaGroup, t11FamNotificationGroup } OBJECT t11FamConfigDomainId MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamConfigDomainIdType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamAutoReconfigure MIN-ACCESS read-only DESCRIPTION "Write access is not required." Expires April 2005 [Page 30] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 OBJECT t11FamContiguousAllocation MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamIfRcfReject MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamIfRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FamRcFabricNotifyEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP t11FamCacheGroup DESCRIPTION "This group is mandatory only for switches which support the concept of Preferred Domain_ID via a best effort attempt for (short-term) re-assignment of the same FC address identifiers." GROUP t11FamCommandGroup DESCRIPTION "This group is optional." ::= { t11FamMIBCompliances 1 } -- Units of Conformance t11FamGroup OBJECT-GROUP OBJECTS { t11FamConfigDomainId, t11FamConfigDomainIdType, t11FamAutoReconfigure, t11FamContiguousAllocation, Expires April 2005 [Page 31] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamPriority, t11FamPrincipalSwitchWwn, t11FamLocalSwitchWwn, t11FamAssignedAreaIdList, t11FamGrantedFcIds, t11FamRecoveredFcIds, t11FamFreeFcIds, t11FamAssignedFcIds, t11FamAvailableFcIds, t11FamRunningPriority, t11FamPrincSwRunningPriority, t11FamState, t11FamPrincipalSwitchSelections, t11FamBuildFabrics, t11FamFabricReconfigures, t11FamDomainId, t11FamLocalPrincipalSwitchSlctns, t11FamIfRcfReject, t11FamIfRole, t11FamIfRowStatus, t11FamRcFabricNotifyEnable, t11FamNotifyFabricIndex, t11FamSticky } STATUS current DESCRIPTION "A collection of general objects for displaying and configuring Fabric Address management." ::= { t11FamMIBGroups 1 } t11FamCommandGroup OBJECT-GROUP OBJECTS { t11FamRestart } STATUS current DESCRIPTION "A collection of objects used for initiating an operation on the Fabric." ::= { t11FamMIBGroups 2 } t11FamDatabaseGroup OBJECT-GROUP OBJECTS { t11FamDatabaseSwitchWwn } STATUS current DESCRIPTION "A collection of objects containing information about Domain-IDs assignments." ::= { t11FamMIBGroups 3 } Expires April 2005 [Page 32] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 t11FamAreaGroup OBJECT-GROUP OBJECTS { t11FamAreaAssignedPortIdList } STATUS current DESCRIPTION "A collection of objects containing information about currently assigned addresses within a Domain." ::= { t11FamMIBGroups 4 } t11FamCacheGroup OBJECT-GROUP OBJECTS { t11FamMaxFcIdCacheSize, t11FamFcIdCacheAreaIdPortId, t11FamFcIdCachePortIds } STATUS current DESCRIPTION "A collection of objects containing information about recently-released Fibre Channel Address Identifiers." ::= { t11FamMIBGroups 5 } t11FamNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { t11FamDomainIdNotAssignedNotify, t11FamNewPrincipalSwitchNotify, t11FamFabricChangeNotify } STATUS current DESCRIPTION "A collection of notifications for status monitoring and notification." ::= { t11FamMIBGroups 6 } END Expires April 2005 [Page 33] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 7. Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. 8. Acknowledgements This document is currently a work item of the INCITS Task Group T11.5. We wish to acknowledge the many contributions and comments from the INCITS Technical Committee T11, including the following: T11 Chair: Robert Snively, Brocade T11 Vice Chair: Claudio Desanti, Cisco Systems T11.5 Chair: Roger Cummings, VERITAS T11.5 members, especially: Ken Hirata, Emulex Scott Kipp, McData Michael O'Donnell, McData Elizabeth G. Rodriguez, Dot Hill Steven L. Wilson, Brocade 9. Normative References [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. Expires April 2005 [Page 34] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M. and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [IF-MIB] McCloghrie, K., and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [FC-MGMT] K. McCloghrie, "Fibre Channel Management MIB", Internet-Draft (draft-ietf-ips-fcmgmt-mib-nn.txt), work-in-progress. [FC-SW-3] "Fibre Channel - Switch Fabric - 3 (FC-SW-3)", ANSI INCITS 384-2004, May 2004. [FC-FS] "Fibre Channel - Framing and Signaling (FC-FS)", ANSI INCITS 373-2003, October 2003. 10. Informative References [RFC2837] Teow, K., "Definitions of Managed Objects for the Fabric Element in Fibre Channel Standard", RFC 2837, May 2000. [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet-Standard Management Framework", RFC 3410, December 2002. [FC-MI] "Fibre Channel - Methodologies for Interconnects (FC-MI)", ANSI INCITS TR-30-2002, November 2002. Expires April 2005 [Page 35] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 11. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. These are the tables and objects and their sensitivity/vulnerability: t11FamConfigDomainId, t11FamConfigDomainIdType and t11FamContiguousAllocation -- ability to change the address allocation policy. t11FamRestart and t11FamAutoReconfigure -- ability to cause a fabric reconfiguration, e.g., on certain error conditions. t11FamPriority -- ability to affect which switch becomes the Principal switch. t11FamRcFabricNotifyEnabl -- ability to enable/disable a notification. t11FamIfRcfReject -- ability to change the switch's behaviour on receipt of an RCF. t11FamIfRowStatus -- ability to change an interface configuration parameter. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may also be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: t11FamTable and t11FamIfTable -- contain the configuration, status and statistics of the Fabric Address Manager. t11FamAreaTable, t11FamDatabaseTable and t11FamFcIdCacheTable -- contain information on currently assigned or recently-released addresses. SNMP versions prior to SNMPv3 did not include adequate security. Expires April 2005 [Page 36] Internet Draft Fibre Channel Fabric Address Manager MIB October 2004 Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementors consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 12. Authors' Addresses Claudio DeSanti Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 408 853-9172 EMail: cds@cisco.com Vinay Gaonkar Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Phone: +1 408 527-8576 EMail: vgaonkar@cisco.com Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA 95134 Phone: +1 408-526-5260 Email: kzm@cisco.com Silvano Gai Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA USA 95134 Phone: +1 408-526-7269 Email: sgai@cisco.com Expires April 2005 [Page 37] Internet Draft Fibre Channel Fabric Address Manager MIB July 2004 13. Full Copyright Statement Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Disclaimer of Validity This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgment Funding for the RFC Editor function is currently provided by the Internet Society. Expires April 2005 [Page 38]